📚 Exam by Category
▾
Objective Questions

Latest APGENCO AEE Electrical Exam Question (Objective Questions), MCQ in English

Subjects : Core Subject (Electrical), General intelligence & Reasoning, General Awareness, English Language & Comprehension, Quantitative Aptitude, Computer Knowledge

Question Bank APGENCO Assistant Executive Engineer (Electrical) Exam - English
Back to Exam

Core Subject (Electrical)

Question 1Single Answer
When a very small amount of higher conducting metal is added to a conductor, its conductivity will 
  1. Aincrease
  2. B decrease
  3. Cremain the same 
  4. Dincrease or decrease depending on the impurity
Question 2Single Answer
A semiconductor differs from a conductor in that it has
  1. AOnly one path for the free electrons in the valence band
  2. BOnly one path for holes in the conduction band
  3. CTwo paths followed by free electrons and holes, one an ordinary path in the conduction band and the other one an extraordinary path in the valence band, respectively 
  4. DTwo paths followed by free electrons and holes, one an extraordinary path in the conduction band and the other one an ordinary path in valence band, respectively 
Question 3Single Answer
Which of the following circuits is used for converting a sine wave into a square wave?
  1. AMonostablemultivibrator
  2. BBistablemultivibrator
  3. CSchmitt trigger circuit 
  4. DDarlington complementary pair
Question 4Single Answer
If a square matrix of order 100 has exactly 15 distinct eigenvalues, then the degree of the minimum polynomial is 
  1. AAt least 15 
  2. BAt most 15 
  3. CAlways 15 
  4. DExactly 100
Question 5Single Answer
For high speed reading and storing of information in a computer, the core shall be of 
  1. AFerrite 
  2. BPiezoelectric 
  3. CPyroelectric 
  4. DFerromagnetic above 768°C
Question 6Single Answer
Assuming both the voltage sources are in phase, the value of R for which maximum power is transferred from circuit A to circuit B is

                 
  1. A0.8 Ω
  2. B1.4 Ω
  3. C2 Ω
  4. D2.8 Ω
Question 7Single Answer
For the intrinsic gallium-arsenide, the conductivity at room temperature 25°C is 10-6 (ohm-m)-1, the electron and hole nobilities are 0.85 m2/V-s and 0.04 m2/V-s respectively. What is the intrinsic carrier concentration at the room temperature?
  1. A7.0 × 1012 m-3
  2. B7.0 × 10-12 m-3
  3. C7.0 × 10-12 m3
  4. D7.0 × 1012 m3
Question 8Single Answer
The resistivity of intrinsic germanium at 30°C is 0.46 –m. What is the intrinsic carrier density at 30°C if the electron mobility is 0.38 m2/V-s and the hole mobility is 0.18 m2/V-s?
  1. A9.2 × 105/m3
  2. B2.77 × 103/m3
  3. C2.43 × 1019/m3
  4. D8.9 × 1012/m3
Question 9Single Answer
Heat conduction in a semiconductor takes place
  1. ABy the mobility of the carriers
  2. BDue to energy gap between conduction band and valency band
  3. CBy the holes and thermal vibrations of atoms
  4. DBy the electrons and thermal vibrations of atoms
Question 10Single Answer
Brewster angle is the angle when a wave is incident on the surface of a perfect dielectric at which there is no reflected wave and the incident wave is
  1. AParallel polarized
  2. BPerpendicularly polarized
  3. CNormally polarized
  4. DNone of the above
Question 11Single Answer
An electrical breakdown of a p-n junction occurs if
  1. AForward voltage increases up to the rating
  2. BReverse voltage increases beyond the rating
  3. CForward voltage decreases below the rating
  4. DReverse voltage decreases below the rating
Question 12Single Answer
The chief deterrent to the widespread application of superconducting materials is
  1. AVery difficult to form, machine or case
  2. BThe difficult in attaining and maintaining extremely low temperature
  3. CThe poor strength-to-weight ratio
  4. DThe lower oxidation rate at elevated temperatures
Question 13Single Answer
Which one of the following properties is not observed in the carbon nanotubes ?
  1. AHigh stiffness and strengths
  2. BLow densities
  3. CUnusual electrical property
  4. DNon-ductile
Question 14Single Answer
The evidence for the importance of electron-phonon interaction in super-conductors comes from
  1. AMeissner effect
  2. BJosephson effect
  3. CIsotope effect
  4. Dx quantization experiments
Question 15Single Answer
Which one of the following materials is used for cable insulation ?
  1. APhenol formaldehyde
  2. BPolytetrafluoroethylene
  3. CPolyvinyl chloride
  4. DAcrylonitrile butadiene styrene
Question 16Single Answer
For high speed reading and storing of information in a computer, the material used is
  1. AFerrite
  2. BPiezoelectric
  3. CPyroelectric
  4. DFerromagnetic above 768°C
Question 17Single Answer
The temperature above which an anti-ferromagnetic material becomes paramagnetic is called
  1. APeak temperature
  2. BNeel temperatur
  3. CCritical temperature
  4. DWeiss temperature
Question 18Single Answer
Which effect is the converse of Peltier effect ?
  1. ASeeback effect
  2. BThomson effect
  3. CHall effect
  4. DJoule effect
Question 19Single Answer
Magnetic materials which may be readily magnetized in either direction are
  1. ASoft magnetic materials
  2. BHard magnetic materials
  3. CHigh eddy current loss materials
  4. DHigh hysteresis loss materials
Question 20Single Answer
Consider the following statements regarding a ferromagnetic material:
1.Below the ferromagnetic Curie temperature, the ferromagnetic materials exhibit hysteresis effect.
2.The coercive force is the filed required to reduce the flux density to zero. 
Which of the above statements is/are correct?
  1. ABoth 1 and 2
  2. BNeither 1 nor 2
  3. C1 only
  4. D2 only
Question 21Single Answer
Resistance switching is normally resorted in case of
  1. AAir blast CB
  2. BBulk oil CB
  3. CMinimum oil CB
  4. DAll types of CB
Question 22Single Answer
By transmitting power at high voltage
  1. Ait will give poor voltage regulation
  2. Bit will give better voltage regulation
  3. Cit will not effect voltage regulation
  4. DNone of these
Question 23Single Answer
Which statement about the daily load curve is valid ?
  1. AThe area under the curve gives the average demand
  2. BThe ratio of the area under the curves to the total area of rectangle in which it is contained gives the load factor for the day
  3. CThe peak of the curve gives the installed capacity of the plant
  4. DThe area of the curves divided by the number of hours gives load factor
Question 24Single Answer
High voltage Schring bridge is used to measure
  1. Alarge capacitance without additional element
  2. Bsmall capacitance without additional element
  3. Cmedium value capacitance
  4. DNone of these
Question 25Single Answer
Draw - in - system of laying underground cables has the drawback (s) of
  1. Ahigher cost
  2. Breduced current carrying capacity of the cables
  3. Crequirements of much deeper and wider trenches
  4. Drepairs, alterations or additions difficult
  5. Eall of the above except
Question 26Single Answer
Surge impedance of a transmission line is
  1. Aindependent of its length
  2. Bdependent on its length
  3. Cindependent on its temperature
  4. Dnone of the above
Question 27Single Answer
If two synchronous generators connected in parallel loose synchronism, it will lead to
  1. Astalling of generators
  2. Bwild fluctuations in current
  3. Cwild fluctuations in current and voltage
  4. DNone of these
Question 28Single Answer
A differential relay responds to
  1. Aalgebraic difference of two or more similar electrical quantities
  2. Bvector difference of two or more similar electrical quantities
  3. Calgebraic difference between two currents
  4. Dalgebraic difference between two voltages
Question 29Single Answer
The conductor carries more current on the surface in comparison to its core. This phenomenon is called the
  1. ASkin effect
  2. BCorona
  3. CFerranti effect
  4. DLenz's effect
Question 30Single Answer
A booster is connected in
  1. Aseries with the feeder
  2. Bparallel with the feeder
  3. Cboth (a) and (b) are correct
  4. Dnone of these
Question 31Single Answer
Fuses have got advantages of
  1. Acheapest type of protection
  2. Binverse time - current characteristic
  3. Cno maintenance
  4. Dcurrent limiting effect under short - circuit conditions
  5. Eall of the above
Question 32Single Answer
The power transmitted will be maximum when
  1. Aline reactance is high
  2. Bcorona losses are minimum
  3. Csending end voltage is more
  4. Dreceiving end voltage is more
Question 33Single Answer
The connected load of a consumer is 2 kW and his maximum demand is 1.5 kW. The load factor of the consumer is
  1. A0.75
  2. B0.375
  3. C1.33
  4. DNone of these
Question 34Single Answer
In a transformer, the exciting current will be in phase quadrature with the impressed voltage provided
  1. Aonly the leakage impedance drop is ignored
  2. Bonly the core loss is ignored
  3. Cboth the leakage impedance drop and the core loss are ignored
  4. Donly the no - load copper loss is ignored
Question 35Single Answer
Which of the following techniques is used for the measurements of a.c. high frequency voltages ?
  1. APeak voltmeter
  2. BSeries resistance mircro - ammeter
  3. CResistance potential divider
  4. DAll of these
Question 36Single Answer
Use of additional shunt capacitor can be made for increasing the capability of line as it
  1. Areduces surge impedance Z0
  2. Bincreases phase shift β
  3. Cincrease in α
  4. Dall of the above
Question 37Single Answer
The sag of a transmission line is least affected owing to
  1. Aweight of the conductor
  2. Bcurrent through the conductor
  3. Catmospheric temperature
  4. Dice deposited on the conductor
Question 38Single Answer
In case of Impulse Thermal break down of solid insulating materials, the critical electric field is proportional to
  1. Acritical absolute temperature
  2. Bsquare of critical absolute temperature
  3. Csquare of T0
  4. Dnone of these
Question 39Single Answer
The insulation of the modern EHV lines is designed based on
  1. Acorona
  2. Bswitching voltages
  3. Clightning voltage
  4. Dall of these
Question 40Single Answer
For constant voltage transmission, the voltage drop along the line is maintained constant by installing
  1. Acapacitors
  2. Binductors
  3. Cresistors
  4. Dsynchronous phase modifiers at the receiving end
Question 41Single Answer
AC network analyser is employed for solving the problems of
  1. Aload flow
  2. Bload flow and stability
  3. Cload flow and short - circuit
  4. Dload flow, stability and short - circuit
Question 42Single Answer
The change in excitation in an alternator connected to an infinite line provides a corresponding change in
  1. Aterminal voltage
  2. Bspeed of rotor
  3. Cpower generated
  4. Dpower factor
Question 43Single Answer
Different types of insulators used for transmission lines are
  1. Apin type only
  2. Bsuspension type only
  3. Cstrain type only
  4. Dpin type, suspension type and shackle type
Question 44Single Answer
The conductor connecting consumer's terminals to the distributor is called the
  1. Afeeder
  2. Bdistributor
  3. Cservice main
  4. Dnone of the above
Question 45Single Answer
Which of the following method or techniques can be used for the measurement of high d.c. voltages ?
  1. AGenerating voltmeter
  2. BElectrostatic voltmeter
  3. CPeak voltmeter
  4. DHalf effect generators
Question 46Single Answer
The ripple voltage in dc output is small if
  1. Afrequency of supply voltage is small
  2. Bthe filtering capacitor is small
  3. Cload current is small
  4. Dnone of these
Question 47Single Answer
The voltage measurements using uniform spark gap are
  1. Aaffected by dust particles
  2. Baffected by polarity of supply
  3. Caffected by temperature
  4. Dnone of these
Question 48Single Answer
Neutral earthing is provided for
  1. Athe safety of personnel from electric shock
  2. Bthe safety of equipment and personnel against lightning and voltage surges
  3. Creducing the voltage stress on lines and equipment with respect to earth under various operating and fault conditions
  4. Dcontrolling the earth fault currents for protective relaying
  5. Eboth (c) and (d)
Question 49Single Answer
The function of Lightning arrester is
  1. Ato limiting the short - circuit fault current
  2. Bto provide path to high voltage surge to earth
  3. Cto reduce arcing
  4. Dnone of these
Question 50Single Answer
In which of the following cases are delay fuses used ?
  1. AFor the protection of light circuits
  2. BFor the protection of power out - let circuits
  3. CFor the protection of fluorescent lamps
  4. DFor the protection of motors
Important Questions Package

APGENCO AEE Electrical Exam Online Question Bank Package

Buy APGENCO AEE Electrical Important Questions, MCQ, question answer in Hindi & English. It will help you to score high marks in APGENCO AEE Electrical question bank 2026 in Online, PDF & Print study material.

+ Free Monthly Current Affairs, GK & more PDF Download
Sr.Package NameAmount
1.APGENCO Assistant Executive Engineer (Electrical) Exam - English
Description : 1000 Question with Answer
₹101 [₹500]
2.APGENCO Assistant Executive Engineer (Electrical) Exam - English
Description : 2000 Question with Answer
₹151 [₹500]
3.APGENCO Assistant Executive Engineer (Electrical) Exam - English
Description : 3000 Question with Answer
₹181 [₹500]
4.APGENCO Assistant Executive Engineer (Electrical) Exam - English
Description : 4000 Question with Answer
₹201 [₹500]
5.APGENCO Assistant Executive Engineer (Electrical) Exam - English
Description : 5000 Question with Answer
₹221 [₹500]
6.APGENCO Assistant Executive Engineer (Electrical) Exam - English
Description : 1000 Question & Answer Download in PDF (Send by Email)
₹151 [₹450]
7.APGENCO Assistant Executive Engineer (Electrical) Exam Question Bank Book - English
Description : 1000 Question with Answer (Printed Material)
₹390 [₹600]
Back to Exam