One bag of Portland cement, 50 kg in weight, would normally have a bulk volume of

AsCu, a preservative for wood, developed by the Forest Research Institute, Dehradun, comprises of chemicals:

Consider the following statements related to autoclave bricks:
1.Less water absorption compared to other bricks.
2.Noise reduction
3.It is cheap compared to other types of bricks.
4.Requirement of bulk volume of mortar in joints being relatively less compared to other types of brick masonry.
5.Not recommended for outer walls. 
Which of the above statements are relevant to the use of ‘autoclave’ bricks? 

The minimum number of annular rings to be seen in every 2.54 cm in the radial direction from the core for timber to be classified as ‘Dense’ is

If the actual thickness of a brick masonry wall is 19 cm, its effective length is 2.70 m, its effective height is 2.82 m and its code specified stiffening coefficient is 1.2 then, for design considerations, the slenderness ratio of the wall will be taken as

Consider the following forms of water in a hydrated cement paste:
1.Capillary water
2.Chemically combined water
3.Interlayer water
4.Adsorbed water 
Which of the above forms of water will, on its/their removal, cause shrinkage of the paste? 

Consider the following statements:High early strength of cement is obtained as a result of
1.Fine grinding.
2.Decreasing the lime content
3.Burning at higher temperature
4.Increasing the quality of gypsum. 
Which of the above statements are correct? 

Consider the following statements related to ‘composite mortar’:
1.Addition of lime to cement mortar improves its workability
2.Composite mortar is obtained by adding 10% by weight of cement and mixing with water.
3.Composite mortar is not preferred in tall buildings.
4.Mechanical grinding is essential for developing composite mortar.Which of the above statements are true in this case? 

Consider the following statements related to ‘non-destructive testing’ of concrete:
1.Indentation test is used to assess the quality of concrete.
2.Resonant Frequency Method is based on a laboratory test.
3.Compressive strength of concrete is estimated through Pulse Velocity Measurement.
4.Dynamic modulus of Elasticity is determined by a Sonometer Test.
5.Thickness of concrete can be estimated by in-situ Rebound Hammer Test. 
Which of the above statements are correct? 

What is the amount of water required for a workable RC of mix 1 : 2: 4 by weight., when W/C is 0-60 and unit weight of concrete is 2400 kg/m³?

Which IS code is used for classification of timber for seasoning purposes?

Consider the following with regard to the application of preservation of timber:
1.Increase in the life span of the member
2.Increase in the strength of the timber
3.Removal of moisture
4.Prevention of growth of fungi by killing them 
Which of the above are correct?

The plies in plywood are so placed that the grains of each ply are

Which of the following is an ODD one as regards ‘requirement of good brick-earth’?

The compressive strength of heavy-duty bricks, as per IS : 2980-1962, should not be less than

Consider the following statements:
1.Brickwork will have high water tightness.
2.Brickwork is preferred for monument structures.
3.Bricks resist fire better than stones
4.Bricks of good quality shall have thin mortar bonds. 
Which of the above statements are correct?

Consider the following statements:A good soil for making bricks should contain
1.30% alumina
2.10% lime nodules
3.Only small quantity of iron oxides
4.15% magnesia 
Which of the above statements are correct?

Which compound of cement is responsible for strength of cement?

Which type of cement is recommended in large mass concrete works such as a dam?

Consider the following statements regarding ‘setting of cement’:
1.Low-heat cement sets faster than OPC.
2.Final setting time decides the strength of cement
3.Initial setting time of Portland Pozzollona is 30 minutes
4.Air-induced setting is observed when stored under damp conditions.
4.Addition of gypsum retards the setting time. 
Which of the above statements are correct? 

A fin will be more effective when Bio number is

A tank of length, breadth and height in the ratio of 2:1:2 is full of water. The ratio of hydrostatic force at the bottom to that at any larger vertical surface is

Which of the following fluids exhibit a certain shear stress at zero shear strain rate followed by a straight line relationship between shear stress and shear strain rate?

What is the specific gravity of a marble stone, which weighs 400N in air, and 200N in water? (g=10m/s²)

What is the intensity of pressure in the following SI units, when specific gravity of mercury is 13.6 and the intensity of pressure is 400KPa ?

Consider the following statements:
1.If a small upward displacement is given to a floating body, it results in the reduction of the buoyant force acting on the body
2.A slight horizontal displacement does not change either the magnitude or the location of the buoyant force 
Which of the above statements is/are correct? 

State whether following flow field is physically possible? 

In a differential manometer, a head of 0.5 m of fluid A in limb 1 is found to balance a head of 0.3 m of fluid B in limb 2. The atmospheric pressure is 760 mm of mercury. The ratio of specific gravities of A to B is

On which of the following just in time manufacturing philosophy emphasizes ?

In a stream line steady flow, two points A and B on a stream line are 1m apart and the flow velocity varies uniformly from 2m/s to 5m/s. What is the acceleration of fluid at B?

The stream function is given by Ψ = 3xy, then the velocity at the point (2,3) is

The boundary layer thickness at a given distance from the leading edge of a flat plate is

In a laminar flow through a circular pipe, the discharge varies

A fluid is flowing over a flat plate. At distance of 8 cm from the leading edge, the Reynolds number is found to be 25600. The thickness of the boundary layer at this point is

Air is flowing over a flat plate with a free stream velocity of 24 m/s, and its kinematic viscosity is 72 ×10^-6m²/s. If at a particular point, the Reynolds number is 30000, its location from the leading edge is

In a refrigerator, the evaporator and condenser coil temperatures are –33°C and 27°C, respectively. Assuming that the maximum COP is realized, the required power input for a refrigerating effect of 4 kW is
 

In a hydraulic coupling

Consider the following statements:
1.The wheel can be operated freely in air
2.Pressure at the exit of the nozzle is atmospheric
3.Pressure does not vary along the moving vanes
4.Change the direction of momentum imparts thrust over moving vanes Which of the following statements are applied to impulse turbine?

A water jet 0.0015m²in area issues from a nozzle with 15 m/s velocity. It is made to impinge perpendicular on to a plate that moves away from the jet with a velocity of 5 m/s. The force on the plate due to this impact is

I go to Madurai by —– Vaigai Express

Have the car stolen!

The payment was collected by the hardworking salesman.

I had to stop all my work to complete this project.

They have published the names of all the successful candidates.

The online shopping site lowered the prices.

Who taught you to drive a truck ?

We shall invite Suresh.

Dark clouds have overcast the evening sky.

The partners will celebrate their triumph tomorrow.