📚 Exam by Category
▾
Objective Questions

Latest CVPP Trainee Engineer and Junior Engineer Recruitment Exam Question (Objective Questions), MCQ in English

Subjects : Electrical Engineer, electrical, Professional Knowledge, Reasoning, English, General English, Quantitative Aptitude, General Awareness

Question Bank CVPP Trainee Engineer and Junior Engineer Exam - English
Back to Exam

Professional Knowledge

Question 1Single Answer
A solid circular shaft needs to be designed to transmit a torque of 50 N-m. If allowable shear stress of the material is 140 MPa, assuming a factor of safety of 2, the minimum allowable design diameter in mm is
  1. A
    8
  2. B
    16
  3. C
    24
  4. D
    32
Question 2Single Answer
The following are the data for two crossed helical gears used for speed reduction: Gear I Pitch circle diameter in the plane of rotation 80 mm and helix angle 30o. Gear II Pitch circle diameter in the plane of rotation 120 mm and helix angle 22.5o. If the input speed is1440 rpm, the output speed in rpm is 
  1. A
    1200  
  2. B
    900
  3. C
    875
  4. D
    720
Question 3Single Answer
If x > y > 1, then, which of the following must be correct?
(i) In x > Iny        (ii) ex > ey
(iii) yx > xx           (iv) cos x > cos y
  1. A
    (i) and (ii)    
  2. B
    (i) and (iii)
  3. C
    (iii) and (iv)
  4. D
    (ii) and (iv)
Question 4Single Answer
Current carrying wire of 10 mm diameter is insulated with 2 mm thickness of insulator of thermal conducting 0.08 W/mK. Heat transfer coefficient of surface is 10 W/m2K. Then correct statement for further addition of insulation is
  1. A
    heat transfer increases
  2. B
    heat transfer decreases
  3. C
    heat transfer increases to maximum then decreases
  4. D
    heat transfer decreases to minimum then increases
Question 5Single Answer
For a long slender column of uniform cross-section, the ratio of critical bucking load for the case with both ends clamped to the case with both ends hinged is 
  1. A
    1 
  2. B
    2
  3. C
    4
  4. D
    8
Question 6Single Answer
If F = 1 kN, the magnitude of the vertical reaction force developed at the point B in kN is
  1. A
    0.63   
  2. B
    0.32
  3. C
    1.26
  4. D
    1.46
Question 7Single Answer
Oil flows through a 200 mm diameter horizontal cast iron pipe (friction) factor f = 0.0225) of length 500 m. The volumetric flow rate is 0/2 m3/s. the head loss (in metre) due to friction is (assume g= 981 m/s2)
  1. A
    116.18
  2. B
    0.116
  3. C
    18.22 
  4. D
    232.36
Question 8Single Answer
If a row interchanged in the matrix, then the  determinant of matrix is
  1. A
    magnitude remains same, sign changes
  2. B
    magnitude changes, sign remains same
  3. C
    both magnitude and sign changes
  4. D
    both magnitude and sign remains same
Question 9Single Answer
A thin walled spherical shell is subjected to an internal pressure. If the radius of the shell is
increased by 1% and the thickness is reduced by 1%, with the internal pressure remaining the same, the percentage change in the circumferential (hoo) stress is
  1. A
    zero 
  2. B
    1
  3. C
    1.08
  4. D
    2.02
Question 10Single Answer
For Rankine cycle with reheat, which of the following is correct?
(i) Increase in average temperature.
(ii) Reduction in thermal efficiency.
(iii) Drier steam at turbine exit.
  1. A
    (i), (ii)  
  2. B
    only (ii) and (iii)
  3. C
    Only (i), (iii) 
  4. D
    All (i), (ii) and (iii)
Question 11Single Answer
The area enclosed between the straight line y = x and parabola y =x2 in the X-Y plane is
  1. A
    1/6
  2. B
    ¼
  3. C
    1/3  
  4. D
    ½
Question 12Single Answer
A flow field which has only convective acceleration is
  1. A
    a steady uniform flow
  2. B
    an unsteady uniform flow
  3. C
    a steady non-uniform flow
  4. D
    an unsteady non-uniform flow
Question 13Single Answer
Kaplan water turbine is commonly used when the flow through its runner is
  1. A
    axial and the head available is more than 100 m
  2. B
    axial and the head available is less than 10 m
  3. C
    radial and the head available is more than 100 m
  4. D
    mixed and the head available is about 50 m
Question 14Single Answer
It is desired to avoid interference in a pair of spur gears having a 200 pressure angle. With increase in pinion to gear speed ratio, the minimum number of teeth on the pinion
  1. A
    increases
  2. B
    decreases
  3. C
    first increases and then decreases
  4. D
    remains unchanged
Question 15Single Answer
Maximum reduction in thickness of one pass in rolling process is ∆hmax, that can be expressed by  ∆hmax = μ2R, where μ is coefficient friction between contact surfaces and R is roller radius. Then, angle subtended by the deformation zone for μ = 0.1 (in degree) is ________
  1. A
    θ = 5.73o
  2. B
    θ = 6.93o
  3. C
    θ = 5.83o
  4. D
    θ = 4.73o
Question 16Single Answer
An ideal gas of mass 1 kg is enclosed in rigid insulated container of volume 1 m3 (Cp = 1000 J/kgK, Cy = 800 J/kgK). A stirring paddle attached in system rotates 1000 rotation with constant rpm has torque 100 N-m, then the final temperature (in K) of  gas is _________
  1. A
    2593185 K
  2. B
    26283185 K
  3. C
    16253185 K
  4. D
    22263185 K
Question 17Single Answer
A machining operation with 400 rpm spindle speed has feed rate 0.4 mm/min and depth of cut 4 mm. Tool has rake angle of 5o. Chip thickness is found 3 mm. The shear angle (in Degree) is __________
  1. A
    6.63o 
  2. B
    5.830
  3. C
    25.500
  4. D
    7.63o  
Question 18Single Answer
Temperature of nitrogen in a vessel of volume 2 m3 is 288 K. A U-tube manometer connected to the vessel shows a reading of 7 cm of mercury (level higher in the end open to atmosphere.). The universal gas constant is 8314 J/kg-mol-K atmospheric pressure is 1.01325 bar, acceleration due to gravity is 9.81 m/s2 and density of mercury is 13600 kg/m3. The mass of  nitrogen (in kg) in the vessel is _______
  1. A
    2.6 kg
  2. B
    1.5 kg
  3. C
    10 kg
  4. D
    .5 kg
Question 19Single Answer
A moist air (10.1 kg) with humidity 0.01 mixed with super heated water vapour, if 0.1 kg uniformly. Then  final humidity of mixture (in kg/kg) is ___________
  1. A
    22.1197 kg/kg dry air
  2. B
    2.0197 kg/kg dry air
  3. C
    0.0197 kg/kg dry air
  4. D
    10.5197 kg/kg dry air
Question 20Single Answer
A single degree of freedom system having mass 1 kg and stiffness 10 kN/m initially at rest is subjected to an impulse force of magnitude 5 kN for 10-4 s/ The amplitude in mm of the resulting free vibration is
  1. A
    0.5 
  2. B
    1.0
  3. C
    5.0
  4. D
    10.0
Question 21Single Answer
CNC machine face with vertices P (0,0,0) , Q (1,1,0) and R (1,1,1), then area of face is _______ n>final humidity of mixture (in kg/kg) is ___________
  1. A
    A = 0.6978
  2. B
    A = 0.7068 
  3. C
    A = 1.7068 
  4. D
    A = 0.6568 
Question 22Single Answer
In the mechanism given below, if the angular velocity of the eccentric circular disc is 1 rad/s, the angular velocity (in rad/s) of the follower link for the instant shown in the figure is
(Note All dimensions are in mm.)
  1. A
    0.05
  2. B
    0.1 
  3. C
    5.0
  4. D
    10.0
Question 23Single Answer
A Carnot Engine (CE1) working between two reservoir A and B, which have temperature TA = 100 K and TB = 500 K. Another Carnot Engine (CE2) works between two reservoir B and c, Tc = 300K. Heat  rejected by (CE1) to reservoir B is completely transferred to (CE2) and heat transferred to (CE1) from reservoir A is 150 MJ then, heat transferred (in MJ) to reservoir C is ___________
  1. A
    450 MJ
  2. B
    550 MJ
  3. C
    100 MJ
  4. D
    950 MJ
Question 24Single Answer
Which one of the following equations is a correct identity for arbitrary  real matrices P, Q and R?
  1. A
    P(Q+R) = PQ + RP
  2. B
    (P-Q)2 =  P2 - 2PQ + Q2
  3. C
    det (P+Q) = det P + det Q
  4. D
    (P + Q)2 = P2 + PQ + QP + Q2
Question 25Single Answer
The exit temperature of the air is
  1. A
    516 K
  2. B
    532 K
  3. C
    484 K
  4. D
    468 K
Question 26Single Answer
For a slider crank mechanism, the velocity and acceleration of the piston at inner dead centre will be : Where ‘  ώ ‘ is angular velocity of the crank and ‘r’ its radius .
  1. A
    0 and 0
  2. B
    0 and ώ²r
  3. C
    0 and < ώ²r
  4. D
    0 and >ώ²r
Question 27Single Answer
----------------------------------------------
Activity      Duration
----------------------------------------------
1-2                 3
2-3                 2
4-3                 3
1-4                 3
2-5                 2

3-5                 2
4-5                 4

-----------------------------------------------
A project has following activities and durations. Then critical path is
  1. A
    1 – 4 – 3 – 5   
  2. B
    1 – 2 – 3 – 5
  3. C
    1 – 2 – 3 – 4
  4. D
    1 – 2 – 5
Question 28Single Answer
A simple mechanism has :
  1. A
    1 link
  2. B
    2 links
  3. C
    3 links 
  4. D
    4 link
Question 29Single Answer
Oldham’s coupling is inversion of -
  1. A
    4- bar chain
  2. B
    6- bar chain
  3. C
    single slider crank chain
  4. D
    double slider crank chain 
Question 30Single Answer
CNC machine interpolator controls
  1. A
    spindle speed  
  2. B
    feed to tool
  3. C
    motion of tools     
  4. D
    None of these
Question 31Single Answer
In arc welding process heat input per unit length is inversely proportional to
  1. A
    voltage    
  2. B
    current
  3. C
    welding     
  4. D
    cycle duty time
Question 32Single Answer
Mohr’s circle may be used to determine following stress on a inclined plane
  1. A
    Normal stress
  2. B
    Principle stress
  3. C
    Tangential stress
  4. D
    All of the above
Question 33Single Answer
In a pipe with constant flow rate, if diameter of pipe is halved and length of pipe is doubled, then the head loss due to friction will be increased by what amount of initial value?
  1. A
    4   
  2. B
    16   
  3. C
    64     
  4. D
    32
Question 34Single Answer
Principle mechanism of material removal in ECM?
  1. A
    Chemical corrosion
  2. B
    Ionic dissolution
  3. C
    Both (a) and (b)
  4. D
    None of the above
Question 35Single Answer
Which of the following is not the unit of distance ?
  1. A
    Light year
  2. B
    Micron
  3. C
    Milimeter
  4. D
    Milestone
Question 36Single Answer
At x = 0, the function f (x) = |x| will be
  1. A
    minimum
  2. B
    maximum
  3. C
    point of inflection
  4. D
    neither minimum nor maximum
Question 37Single Answer
The unit of work is  :
  1. A
    kW
  2. B
    KWh
  3. C
    KW/H
  4. D
    kJ/s
Question 38Single Answer
In a pipe with constant flow rate, if diameter of pipe is halved and length of pipe is doubled, then the head loss due to friction will be increased by what amount of initial value?
  1. A
    4 
  2. B
    16
  3. C
    64
  4. D
    32
Question 39Single Answer
Ratio of solidification time f a cylindrical casting (height = radius) to the cubic casting of side two times the height of cylindrical casting is __________
 
  1. A
    0.25
  2. B
    1
  3. C
    5.0
  4. D
    7.5
  5. E
    10
Question 40Single Answer
Closely same meaning to word Awkward
  1. A
    Incet   
  2. B
    Dreadful
  3. C
    Graceful
  4. D
    Suitable
Question 41Single Answer
An orthogonal turning operation is carried out under the following conditions: rake angle = 5o, spindle  rotational speed  = 400rpm, axial feed = 0.4 m/min and radial depth of cut = 5 mm. The chip thickness tc i9s found to be 3 mm. The shear angle (in degree) in this turning process is __________
  1. A
    220
  2. B
    32.24o
  3. C
    55.50
  4. D
    100
Question 42Single Answer
Packing factor for BCC structure is (numerical type) ____________
  1. A
    APF = 0.68
  2. B
    APF = 0.7
  3. C
    APF = 9.68
  4. D
    APF = 1.68
Question 43Single Answer
In insulated turbine, expansion takes place isentropically from State 1 and 20% of mass bleed at 20 kPa and remaining expanded to State 3, 9 kPa. At  state 1, m = 100 kg/s h1 = 3486 kJ/kg State 2, steam is dry saturated with h2 = 2776 kJ/kg and State 3, P = 9 kPa, hf, hg, sf, sg, then total work output of turbine (in MW) is _________
  1. A
    2100.56 MW
  2. B
    2025.56 MW
  3. C
    2125.56 MW
  4. D
    2005.56 MW
Question 44Single Answer
A venturimeter is attached to pipe of 80 mm diameter has throat of 40 mm diameter. It is found that pressure in the pipe and at throat is 400 kPa and 130 kPa, respectively. Velocity of the flow in the pipe (in m/s) is _________
  1. A
    6 m/s
  2. B
    2 m/s
  3. C
    0 m/s
  4. D
    54 m/s
Question 45Single Answer
A column of length 1 m is hinged at both ends has cross-section (10x20)mm2. Young’s modulus of  elasticity is 200GPa. The maximum permissible axial compressive load can apply (in N) is ___________
  1. A
    328773 N 
  2. B
    228653 N
  3. C
    328653 N 
  4. D
    308653 N
Question 46Single Answer
In a spring mass system, the mass is m and spring constant is k. The critical damping coefficient of the system is 0.1 kg/s. In another spring mass system, the mass is 2m and the spring constant is 8k. The critical damping coefficient of the system (in kg/s) is  __________
  1. A
    0.4 kg/s
  2. B
    1.4 kg/s
  3. C
    1.5 kg /s
  4. D
    1.50 kg/s
Question 47Single Answer
Annual demand of a product is 50000 and ordering  cost is Rs. 7000 per order and EOQ is 10000 units. At  optimum annual inventory, total yearly holding cost is _________Rs. 
  1. A
    Rs. 15000
  2. B
    Rs. 10000
  3. C
    Rs. 55000
  4. D
    Rs. 35000
Question 48Single Answer
Which one of the following configurations has thehighest fin effectiveness?
  1. A
    Thin, closely spaced fins
  2. B
    Thin, widely spaced fins
  3. C
    Thick, widely spaced fins
  4. D
    Thick, closely spaced fins
Question 49Single Answer
The maximum force F in kN that can be applied at C such that the axial stress in any of the truss member does not exceed 100 MPa is
  1. A
    8.87
  2. B
    11.15 
  3. C
    14.14 
  4. D
    22.30
Question 50Single Answer
Specific enthalpy and velocity of steam at inlet and exit of a steam turbine, running under steady state, are as given below. 
Steam Condition Specific Enthalpy (kJ/kg) Velocity (m/s)
Intel steam condition 3250 180
Exit steam condition 2360 5

The rate of heat loss from the turbine per kg of steam flow rate is 5 kW. Neglecting changes in potential energy of steam, the power developed in kW by the steam turbine per kg of steam flow rate, is
  1. A
    901.2   
  2. B
    911.2
  3. C
    17072.5     
  4. D
    17082.5
Important Questions Package

CVPP Trainee Engineer and Junior Engineer Recruitment Exam Online Question Bank Package

Buy CVPP Trainee Engineer and Junior Engineer Recruitment Important Questions, MCQ, question answer in Hindi & English. It will help you to score high marks in CVPP Trainee Engineer and Junior Engineer Recruitment question bank 2026 in Online, PDF & Print study material.

+ Free Monthly Current Affairs, GK & more PDF Download
Sr.Package NameAmount
1.CVPP Trainee Engineer and Junior Engineer Exam - English
Description : 2500 Question with Answer
₹100 [₹500]
Back to Exam
Question for CVPP Trainee Engineer and Junior Engineer Recruitment 2026 - Quiz / Questions / MCQ - Toppersexam