📚 Exam by Category
▾
Objective Questions

Latest DRDO CEPTAM Senior Technical Assistant Electrical Exam Question (Objective Questions), MCQ in English

Subjects : Electrical

Question Bank DRDO CEPTAM Senior Technical Assistant (Electrical) Exam Tier 2 - English
Back to Exam

Electrical

Question 1Single Answer
When a very small amount of higher conducting metal is added to a conductor, its conductivity will 
  1. A
    increase
  2. B
     decrease
  3. C
    remain the same 
  4. D
    increase or decrease depending on the impurity
Question 2Single Answer
An electrically balanced atom has 30 protons in its nucleus and 2 electrons in its outermost shell. The materials made of such atom is
  1. A
    a conductor
  2. B
    an insulator
  3. C
    a semiconductor 
  4. D
    a superconductor
Question 3Single Answer
The temperature coefficient of resistance of a doped semiconductor is
  1. A
    always positive
  2. B
    always negative
  3. C
    zero 
  4. D
    positive or negative depending upon the level of doping 
Question 4Single Answer
In the slice processing of an integrated circuit
  1. A
    components are formed in the areas where silicon dioxide remains
  2. B
    components are formed in the areas where silicon dioxide has been removed
  3. C
    the diffusing elements diffuse through silicon dioxide 
  4. D
    only on diffusion process is used 
Question 5Single Answer
Permanent magnet loses the magnetic behaviour when heated because of
1. atomic vibration
2. dipole vibration
3. realignment of dipoles
Which of the above are correct?
  1. A
    1  and 2 only 
  2. B
    1 and 3 only
  3. C
    1, 2 and 3         
  4. D
    2 and 3
Question 6Single Answer
A semiconductor differs from a conductor in that it has
  1. A
    Only one path for the free electrons in the valence band
  2. B
    Only one path for holes in the conduction band
  3. C
    Two paths followed by free electrons and holes, one an ordinary path in the conduction band and the other one an extraordinary path in the valence band, respectively 
  4. D
    Two paths followed by free electrons and holes, one an extraordinary path in the conduction band and the other one an ordinary path in valence band, respectively 
Question 7Single Answer
Which of the following circuits is used for converting a sine wave into a square wave?
  1. A
    Monostablemultivibrator
  2. B
    Bistablemultivibrator
  3. C
    Schmitt trigger circuit 
  4. D
    Darlington complementary pair
Question 8Single Answer
Which of the following elements of electrical engineering cannot be analyzed using Ohm’s law ?
  1. A
    Capacitors
  2. B
    Inductors
  3. C
    Transistors
  4. D
    Resistance
Question 9Single Answer
Consider the following statements: A power supply uses bridge rectifier with a capacitor input filter. If one of the diodes is defective, then
1. The dc load voltage will be lower than its expected value
2. Ripple frequency will be lower than its expected value
3. The surge current will increase considerably
Which of the above statements are correct?
  1. A
    1  and 2 only 
  2. B
    1 and 3 only
  3. C
    2 and 3 only 
  4. D
    1, 2 and 3 
Question 10Single Answer
Three identical amplifiers each having a voltage gain of 50 are cascaded. The open loop voltage gain of the combined amplifier is
  1. A
    71 dB 
  2. B
    82 dB 
  3. C
    91 dB 
  4. D
    102 dB 
Question 11Single Answer
If a square matrix of order 100 has exactly 15 distinct eigenvalues, then the degree of the minimum polynomial is 
  1. A
    At least 15 
  2. B
    At most 15 
  3. C
    Always 15 
  4. D
    Exactly 100
Question 12Single Answer
For high speed reading and storing of information in a computer, the core shall be of 
  1. A
    Ferrite 
  2. B
    Piezoelectric 
  3. C
    Pyroelectric 
  4. D
    Ferromagnetic above 768°C
Question 13Single Answer
Soft magnetic materials should have 
  1. A
    Large saturation magnetization and large permeability 
  2. B
    Low saturation magnetization and large permeability 
  3. C
    Large saturation magnetization and low permeability 
  4. D
    Low saturation magnetization and low permeability 
Question 14Single Answer
Orbital magnetic moment of an electron, in an atom, is of the order of 
  1. A
    0.1 Bohr magneton 
  2. B
    1.0 Bohr magneton 
  3. C
    10 Bohr magneton 
  4. D
    100 Bohr magneton
Question 15Single Answer
When the temperature of a ferromagnetic material exceeds the Curie temperature, it behaves similar to a 
  1. A
    Diamagnetic material 
  2. B
    Ferrimagnetic material 
  3. C
    Paramagnetic material 
  4. D
     Antiferromagnetic material
Question 16Single Answer
Assuming both the voltage sources are in phase, the value of R for which maximum power is transferred from circuit A to circuit B is
  1. A
    0.8 Ω
  2. B
    1.4 Ω
  3. C
    2 Ω
  4. D
    2.8 Ω
Question 17Single Answer
For the intrinsic gallium-arsenide, the conductivity at room temperature 25°C is 10-6 (ohm-m)-1, the electron and hole nobilities are 0.85 m2/V-s and 0.04 m2/V-s respectively. What is the intrinsic carrier concentration at the room temperature?
  1. A
    7.0 × 1012 m-3
  2. B
    7.0 × 10-12 m-3
  3. C
    7.0 × 10-12 m3
  4. D
    7.0 × 1012 m3
Question 18Single Answer
The resistivity of intrinsic germanium at 30°C is 0.46 –m. What is the intrinsic carrier density at 30°C if the electron mobility is 0.38 m2/V-s and the hole mobility is 0.18 m2/V-s?
  1. A
    9.2 × 105/m3
  2. B
    2.77 × 103/m3
  3. C
    2.43 × 1019/m3
  4. D
    8.9 × 1012/m3
Question 19Single Answer
Heat conduction in a semiconductor takes place
  1. A
    By the mobility of the carriers
  2. B
    Due to energy gap between conduction band and valency band
  3. C
    By the holes and thermal vibrations of atoms
  4. D
    By the electrons and thermal vibrations of atoms
Question 20Single Answer
Brewster angle is the angle when a wave is incident on the surface of a perfect dielectric at which there is no reflected wave and the incident wave is
  1. A
    Parallel polarized
  2. B
    Perpendicularly polarized
  3. C
    Normally polarized
  4. D
    None of the above
Question 21Single Answer
Resistance switching is normally resorted in case of
  1. A
    Air blast CB
  2. B
    Bulk oil CB
  3. C
    Minimum oil CB
  4. D
    All types of CB
Question 22Single Answer
By transmitting power at high voltage
  1. A
    it will give poor voltage regulation
  2. B
    it will give better voltage regulation
  3. C
    it will not effect voltage regulation
  4. D
    None of these
Question 23Single Answer
Which statement about the daily load curve is valid ?
  1. A
    The area under the curve gives the average demand
  2. B
    The ratio of the area under the curves to the total area of rectangle in which it is contained gives the load factor for the day
  3. C
    The peak of the curve gives the installed capacity of the plant
  4. D
    The area of the curves divided by the number of hours gives load factor
Question 24Single Answer
High voltage Schring bridge is used to measure
  1. A
    large capacitance without additional element
  2. B
    small capacitance without additional element
  3. C
    medium value capacitance
  4. D
    None of these
Question 25Single Answer
Draw - in - system of laying underground cables has the drawback (s) of
  1. A
    higher cost
  2. B
    reduced current carrying capacity of the cables
  3. C
    requirements of much deeper and wider trenches
  4. D
    repairs, alterations or additions difficult
  5. E
    all of the above except
Question 26Single Answer
What is the primary purpose of Kirchhoff's Current Law (KCL)?
  1. A
    To ensure conservation of charge at a node
  2. B
    To calculate voltage drops
  3. C
    To determine power dissipation
  4. D
    To analyze resonance
Question 27Single Answer
In a circuit with three resistors in series, each of 5 Ω, what is the equivalent resistance?
  1. A
    5 Ω
  2. B
    15 Ω
  3. C
    67 Ω
  4. D
    10 Ω
Question 28Single Answer
What is the voltage across a 10 Ω resistor carrying a current of 2 A?
  1. A
    5 V
  2. B
    10 V
  3. C
    20 V
  4. D
    40 V
Question 29Single Answer
Which analysis technique uses loop currents as variables to solve a circuit?
  1. A
    Nodal analysis
  2. B
    Mesh analysis
  3. C
    Superposition theorem
  4. D
    Thevenin’s theorem
Question 30Single Answer
The Superposition theorem is applicable to:
  1. A
    Non-linear circuits
  2. B
    Linear bilateral circuits
  3. C
    Unilateral circuits
  4. D
    Time-varying circuits
Question 31Single Answer
Thevenin’s theorem converts a complex circuit into:
  1. A
    A single current source and parallel resistance
  2. B
    A single resistor
  3. C
    A single voltage source and series resistance
  4. D
    A single capacitor
Question 32Single Answer
For maximum power transfer, the load resistance should be:
  1. A
    Half of the source resistance
  2. B
    Equal to the source resistance
  3. C
    Twice the source resistance
  4. D
    Zero
Question 33Single Answer
Norton’s theorem is the dual of:
  1. A
    Thevenin’s theorem
  2. B
    Superposition theorem
  3. C
    Millman’s theorem
  4. D
    Reciprocity theorem
Question 34Single Answer
Millman’s theorem is used to find:
  1. A
    Equivalent resistance
  2. B
    Current through a resistor
  3. C
    Voltage across parallel branches
  4. D
    Power dissipation
Question 35Single Answer
Tellegen’s theorem is based on:
  1. A
    Conservation of energy
  2. B
    Conservation of charge
  3. C
    Maximum power transfer
  4. D
    Resonance
Question 36Single Answer
In graph theory, a tree of a network graph contains:
  1. A
    All nodes and some branches
  2. B
    All branches and some nodes
  3. C
    Only loops
  4. D
    Only capacitors
Question 37Single Answer
The rank of an incidence matrix for a graph with n nodes is:
  1. A
    n
  2. B
    n - 1
  3. C
    n + 1
  4. D
    2n
Question 38Single Answer
A cut-set in a network graph includes:
  1. A
    All branches of the graph
  2. B
    Only resistors
  3. C
    Branches that disconnect the graph when removed
  4. D
    Only loops
Question 39Single Answer
The tie-set matrix is associated with:
  1. A
    Nodes
  2. B
    Loops
  3. C
    Cut-sets
  4. D
    Resistors
Question 40Single Answer
The number of fundamental loops in a graph with b branches, n nodes, and t twigs is:
  1. A
    b - n + 1
  2. B
    n - 1
  3. C
    b - t
  4. D
    t - n
Question 41Single Answer
What is the basis of energy balance in electromechanical systems?
  1. A
    Input Energy = Output Energy
  2. B
    Input Energy = Mechanical Work + Stored Energy + Losses
  3. C
    Input Energy = Stored Energy Only
  4. D
    Input Energy = Losses Only
Question 42Single Answer
What is the primary coupling field in rotating machines?
  1. A
    Electric field
  2. B
    Magnetic field
  3. C
    Gravitational field
  4. D
    Thermal field
Question 43Single Answer
What is a condition for electromechanical energy conversion?
  1. A
    Static magnetic field only
  2. B
    Mechanical motion and electrical current
  3. C
    High temperature
  4. D
    Low voltage
Question 44Single Answer
How is energy stored in a magnetic field calculated?
  1. A
    ( Wm = Li2 )
  2. B
    ( Wm = frac{1}{2}Li2 )
  3. C
    ( Wm = Psi i )
  4. D
    ( Wm = frac{1}{2}Psi2 )
Question 45Single Answer
What is co-energy in a magnetic system?
  1. A
    ( Wm' = int Psi di )
  2. B
    ( Wm' = frac{1}{2}Li^2 )
  3. C
    ( Wm' = Psi i )
  4. D
    ( Wm' = frac{1}{2}Psi2 )
Question 46Single Answer
How is force derived from stored energy at constant current?
  1. A
    ( F = -frac{partial Wm(x,i)}{partial x} )
  2. B
    ( F = +frac{partial Wm(x,i)}{partial x} )
  3. C
    ( F = -frac{partial Wm'(x,Psi)}{partial x} )
  4. D
    ( F = +frac{partial Wm'(x,Psi)}{partial x} )
Question 47Single Answer
What produces reluctance torque?
  1. A
    Maximum flux linkage
  2. B
    Minimum reluctance path alignment
  3. C
    High voltage
  4. D
    Low current
Question 48Single Answer
What characterizes a singly excited system?
  1. A
    Two electrical inputs
  2. B
    One electrical input
  3. C
    No electrical input
  4. D
    Multiple mechanical inputs
Question 49Single Answer
Which machine is an example of a doubly excited system?
  1. A
    Reluctance motor
  2. B
    Capacitor motor
  3. C
    Electromagnet
  4. D
    Synchronous machine
Question 50Single Answer
What causes transformer EMF?
  1. A
    Conductor motion
  2. B
    Time-varying flux
  3. C
    Constant flux
  4. D
    Mechanical work
Important Questions Package

DRDO CEPTAM Senior Technical Assistant Electrical Exam Online Question Bank Package

Buy DRDO CEPTAM Senior Technical Assistant Electrical Important Questions, MCQ, question answer in Hindi & English. It will help you to score high marks in DRDO CEPTAM Senior Technical Assistant Electrical question bank 2026 in Online, PDF & Print study material.

+ Free Monthly Current Affairs, GK & more PDF Download
Sr.Package NameAmount
1.DRDO CEPTAM Senior Technical Assistant (Electrical) Exam Tier 1 - Hindi
Description : 1000 Question with Answer
₹101 [₹500]
2.DRDO CEPTAM Senior Technical Assistant (Electrical) Exam Tier 1 - Hindi
Description : 2000 Question with Answer
₹141 [₹500]
3.DRDO CEPTAM Senior Technical Assistant (Electrical) Exam Tier 1 - Hindi
Description : 3000 Question with Answer
₹171 [₹500]
4.DRDO CEPTAM Senior Technical Assistant (Electrical) Exam Tier 1 - Hindi
Description : 4000 Question with Answer
₹201 [₹500]
5.DRDO CEPTAM Senior Technical Assistant (Electrical) Exam Tier 1 - English
Description : 1000 Question with Answer
₹101 [₹500]
6.DRDO CEPTAM Senior Technical Assistant (Electrical) Exam Tier 1 - English
Description : 2000 Question with Answer
₹141 [₹500]
7.DRDO CEPTAM Senior Technical Assistant (Electrical) Exam Tier 1 - English
Description : 3000 Question with Answer
₹171 [₹500]
8.DRDO CEPTAM Senior Technical Assistant (Electrical) Exam Tier 1 - English
Description : 4000 Question with Answer
₹201 [₹500]
9.DRDO CEPTAM Senior Technical Assistant (Electrical) Exam Tier 2 - Hindi
Description : 1000 Question with Answer
₹101 [₹500]
10.DRDO CEPTAM Senior Technical Assistant (Electrical) Exam Tier 2 - Hindi
Description : 2000 Question with Answer
₹141 [₹500]
11.DRDO CEPTAM Senior Technical Assistant (Electrical) Exam Tier 2 - Hindi
Description : 3000 Question with Answer
₹171 [₹500]
12.DRDO CEPTAM Senior Technical Assistant (Electrical) Exam Tier 2 - English
Description : 1000 Question with Answer
₹101 [₹500]
13.DRDO CEPTAM Senior Technical Assistant (Electrical) Exam Tier 2 - English
Description : 2000 Question with Answer
₹141 [₹500]
14.DRDO CEPTAM Senior Technical Assistant (Electrical) Exam Tier 2 - English
Description : 3000 Question with Answer
₹171 [₹500]
15.DRDO CEPTAM Senior Technical Assistant (Electrical) Exam Tier 1 - Hindi
Description : 1000 Question & Answer Download in PDF (Send by Email)
₹151 [₹450]
16.DRDO CEPTAM Senior Technical Assistant (Electrical) Exam Tier 2 - Hindi
Description : 1000 Question & Answer Download in PDF (Send by Email)
₹151 [₹450]
17.DRDO CEPTAM Senior Technical Assistant (Electrical) Exam Tier 1 - English
Description : 1000 Question & Answer Download in PDF (Send by Email)
₹151 [₹450]
18.DRDO CEPTAM Senior Technical Assistant (Electrical) Exam Tier 2 - English
Description : 1000 Question & Answer Download in PDF (Send by Email)
₹151 [₹450]
19.DRDO CEPTAM Senior Technical Assistant (Electrical) Exam Question Bank Book Tier 1 - Hindi
Description : 1000 Question with Answer (Printed Material)
₹450 [₹800]
20.DRDO CEPTAM Senior Technical Assistant (Electrical) Exam Question Bank Book Tier 2 - Hindi
Description : 1000 Question with Answer (Printed Material)
₹450 [₹800]
21.DRDO CEPTAM Senior Technical Assistant (Electrical) Exam Question Bank Book Tier 1 - English
Description : 1000 Question with Answer (Printed Material)
₹390 [₹600]
22.DRDO CEPTAM Senior Technical Assistant (Electrical) Exam Question Bank Book Tier 2 - English
Description : 1000 Question with Answer (Printed Material)
₹390 [₹600]
Back to Exam