Download AppGovt. JobsFree G.K. & Current AffairsScholarshipBlog
Free PracticeContact
📚 Exam by Category
▾
Objective Questions

Latest IMTECH Chandigarh Technician Exam Question (Objective Questions), MCQ in English

Subjects : Electrical

Question Bank IMTECH Chandigarh Technical Assistant Exam Paper III - English
Back to Exam

Electrical

Question 1Single Answer
Assuming both the voltage sources are in phase, the value of R for which maximum power is transferred from circuit A to circuit B is
  1. A
    0.8 Ω
  2. B
    1.4 Ω
  3. C
    2 Ω
  4. D
    2.8 Ω
Question 2Single Answer
For the intrinsic gallium-arsenide, the conductivity at room temperature 25°C is 10-6 (ohm-m)-1, the electron and hole nobilities are 0.85 m2/V-s and 0.04 m2/V-s respectively. What is the intrinsic carrier concentration at the room temperature?
  1. A
    7.0 × 1012 m-3
  2. B
    7.0 × 10-12 m-3
  3. C
    7.0 × 10-12 m3
  4. D
    7.0 × 1012 m3
Question 3Single Answer
The resistivity of intrinsic germanium at 30°C is 0.46 –m. What is the intrinsic carrier density at 30°C if the electron mobility is 0.38 m2/V-s and the hole mobility is 0.18 m2/V-s?
  1. A
    9.2 × 105/m3
  2. B
    2.77 × 103/m3
  3. C
    2.43 × 1019/m3
  4. D
    8.9 × 1012/m3
Question 4Single Answer
Heat conduction in a semiconductor takes place
  1. A
    By the mobility of the carriers
  2. B
    Due to energy gap between conduction band and valency band
  3. C
    By the holes and thermal vibrations of atoms
  4. D
    By the electrons and thermal vibrations of atoms
Question 5Single Answer
Brewster angle is the angle when a wave is incident on the surface of a perfect dielectric at which there is no reflected wave and the incident wave is
  1. A
    Parallel polarized
  2. B
    Perpendicularly polarized
  3. C
    Normally polarized
  4. D
    None of the above
Question 6Single Answer
An electrical breakdown of a p-n junction occurs if
  1. A
    Forward voltage increases up to the rating
  2. B
    Reverse voltage increases beyond the rating
  3. C
    Forward voltage decreases below the rating
  4. D
    Reverse voltage decreases below the rating
Question 7Single Answer
The chief deterrent to the widespread application of superconducting materials is
  1. A
    Very difficult to form, machine or case
  2. B
    The difficult in attaining and maintaining extremely low temperature
  3. C
    The poor strength-to-weight ratio
  4. D
    The lower oxidation rate at elevated temperatures
Question 8Single Answer
Which one of the following properties is not observed in the carbon nanotubes ?
  1. A
    High stiffness and strengths
  2. B
    Low densities
  3. C
    Unusual electrical property
  4. D
    Non-ductile
Question 9Single Answer
The evidence for the importance of electron-phonon interaction in super-conductors comes from
  1. A
    Meissner effect
  2. B
    Josephson effect
  3. C
    Isotope effect
  4. D
    x quantization experiments
Question 10Single Answer
Which one of the following materials is used for cable insulation ?
  1. A
    Phenol formaldehyde
  2. B
    Polytetrafluoroethylene
  3. C
    Polyvinyl chloride
  4. D
    Acrylonitrile butadiene styrene
Question 11Single Answer
For high speed reading and storing of information in a computer, the material used is
  1. A
    Ferrite
  2. B
    Piezoelectric
  3. C
    Pyroelectric
  4. D
    Ferromagnetic above 768°C
Question 12Single Answer
The temperature above which an anti-ferromagnetic material becomes paramagnetic is called
  1. A
    Peak temperature
  2. B
    Neel temperatur
  3. C
    Critical temperature
  4. D
    Weiss temperature
Question 13Single Answer
Which effect is the converse of Peltier effect ?
  1. A
    Seeback effect
  2. B
    Thomson effect
  3. C
    Hall effect
  4. D
    Joule effect
Question 14Single Answer
Magnetic materials which may be readily magnetized in either direction are
  1. A
    Soft magnetic materials
  2. B
    Hard magnetic materials
  3. C
    High eddy current loss materials
  4. D
    High hysteresis loss materials
Question 15Single Answer
Consider the following statements regarding a ferromagnetic material:
1.Below the ferromagnetic Curie temperature, the ferromagnetic materials exhibit hysteresis effect.
2.The coercive force is the filed required to reduce the flux density to zero. 
Which of the above statements is/are correct?
  1. A
    Both 1 and 2
  2. B
    Neither 1 nor 2
  3. C
    1 only
  4. D
    2 only
Question 16Single Answer
The impact ionization phenomenon in semiconductor may be viewed as the reverse process of
  1. A
    Radiative recombination
  2. B
    Auger recombination
  3. C
    Surface recombination
  4. D
    Shockley-Read-Hall recombination
Question 17Single Answer
Refractive index of a slice glass can be reduced by doping it with tiny amount of
  1. A
    GeO2
  2. B
    B2O3
  3. C
    P2O5x
  4. D
    Al2O3
Question 18Single Answer
If a diameter of a copper wire is increased by two times keeping its terminal voltage same, then the drift velocity will
  1. A
    Become twice
  2. B
    Become half
  3. C
    ecome four times
  4. D
    Remain unchanged
Question 19Single Answer
In an induction type energy meter, the steady speed attained by the rotating disc is
1.Proportional to the deflecting torque.
2.Proportional to the resistance of the path of eddy currents.
3.Inversely proportional to the effective readings of disc from its axis.
4.Inversely proportional to the square of brake magnetic flux. 
Which of the above are correct?
  1. A
    1, 2 and 3 only
  2. B
    1, 2 and 4 only
  3. C
    2, 3 and 4 only
  4. D
    1, 2, 3 and 4
Question 20Single Answer
If ‘KCLFTSB’ stands for ‘best of  luck’ and ‘SHSWDG’ stands for ‘good wishes’, which of the following indicates ‘ace the exam’?
  1. A
    MCHTX
  2. B
    MXHTC
  3. C
    XMHCT
  4. D
    XMHTC
Question 21Single Answer
Consider  the following statements associated with the basic electrostatic properties of ideal conductors:
1.The resultant field inside is zero.
2.The net charge density in the interior is zero.
3.Any net charges reside on the surface.
4.The surface is always equipotential.
5.The field just outside is zero. 
Which of the above statements are correct?
  1. A
    1, 2, 3 and 4
  2. B
    3, 4 and 5 only
  3. C
    1, 2 and 3 only
  4. D
    2 and 3 only
Question 22Single Answer
A semiconductor device made out of a material having very high temperature coefficient of resistance is
  1. A
    Transistor
  2. B
    Varistor
  3. C
    Thyristor
  4. D
    Thermistor
Question 23Single Answer
The electrical conductivity of a semiconductor increases with increase in temperature because
  1. A
    The carrier concentration increases
  2. B
    The mobility of carrier increases
  3. C
    Both carrier concentration and mobility increases
  4. D
    The band gap decreases
Question 24Single Answer
Which of the following are associated with soft superconductors?
1.Silsbee’s rule
2.Meissner effect
3.Faraday rotation
4.Curie-Weiss law
  1. A
    2, 3 and 4
  2. B
    1 and 3 only
  3. C
    1 and 2 only
  4. D
    2 and 3 only
Question 25Single Answer
In a two-channel oscilloscope operating in x-y mode, two in-phase 50 Hz sinusoidal waveforms of equal amplitude are fed to the two channels. What will be the resultant pattern on the screen?
  1. A
    An ellipse
  2. B
    A parabola
  3. C
    Straight line inclined at 45 with respect to x-axis
  4. D
    A circle
Question 26Single Answer
When a very small amount of higher conducting metal is added to a conductor, its conductivity will 
  1. A
    increase
  2. B
     decrease
  3. C
    remain the same 
  4. D
    increase or decrease depending on the impurity
Question 27Single Answer
An electrically balanced atom has 30 protons in its nucleus and 2 electrons in its outermost shell. The materials made of such atom is
  1. A
    a conductor
  2. B
    an insulator
  3. C
    a semiconductor 
  4. D
    a superconductor
Question 28Single Answer
The temperature coefficient of resistance of a doped semiconductor is
  1. A
    always positive
  2. B
    always negative
  3. C
    zero 
  4. D
    positive or negative depending upon the level of doping 
Question 29Single Answer
In the slice processing of an integrated circuit
  1. A
    components are formed in the areas where silicon dioxide remains
  2. B
    components are formed in the areas where silicon dioxide has been removed
  3. C
    the diffusing elements diffuse through silicon dioxide 
  4. D
    only on diffusion process is used 
Question 30Single Answer
Permanent magnet loses the magnetic behaviour when heated because of
1. atomic vibration
2. dipole vibration
3. realignment of dipoles
Which of the above are correct?
  1. A
    1  and 2 only 
  2. B
    1 and 3 only
  3. C
    1, 2 and 3         
  4. D
    2 and 3
Question 31Single Answer
A Zener regulator has an input voltage varying between 20 V and 30 V. The desired regulated voltage is 12 V, while the load varies between 140  and 10k  The maximum resistance in series with the unregulated source and Zener diode would be
  1. A
    3.3
  2. B
    6.6
  3. C
    36.6
  4. D
    93.3
Question 32Single Answer
A short in any type of circuit (series, parallel or combination) causes the total circuit
1. resistance to decrease
2. power to decreases
3. current to increase
Which of the above are correct?
  1. A
    2  and 3 
  2. B
    2 and 4
  3. C
    1 and 4 
  4. D
    1 and 3 
Question 33Single Answer
An air-cored solenoid of 250 turns has a cross-sectional area A = 80 cm2 and length l = 100 cm. The value of its inductance is
  1. A
    0.425 mH          
  2. B
    0.628 mH
  3. C
    0.751 mH 
  4. D
    0.904 mH
Question 34Single Answer
The current in a coil changes uniformly from 10 A to 1 A in half a second. A voltmeter connected across the coil gives a reading of 36 V. The self-inductance of the coil is
  1. A
    0.5 H 
  2. B
    1 H
  3. C
    2 H       
  4. D
    4 H 
Question 35Single Answer
In a mutually coupled circuit, the primary current is reduced from 4A to zero in 10 s.  A voltage of 40000 V is observed across the secondary. The mutual inductance between the coils is
  1. A
    100 H 
  2. B
    10 H
  3. C
    0.1 H 
  4. D
    0.01 H 
Question 36Single Answer
A CRO screen has 10 divisions on the horizontal scale. If a voltage signal 5 sin (314t + 45°) is examined with a line base setting of 5 ms/div, the number of signals displayed on the screen will be 
  1. A
    1.25 cycles           
  2. B
    2.5 cycles 
  3. C
    5 cycles 
  4. D
    10 cycles 
Question 37Single Answer
Which one of the following conditions will be correct when three identical bulbs forming a star are connected to a three-phase balanced supply?
 
  1. A
    The bulb in R phase will be the brightest 
  2. B
    The bulb in Y phase will be the brightest 
  3. C
    The bulb in B phase will be the brightest 
  4. D
    All the bulbs will be equally bright 
Question 38Single Answer
Loading by the measuring instruments introduces an error in the measured parameter. Which of the following devices gives most accurate result?
  1. A
    PMMC
  2. B
    Hot-wire
  3. C
    CRO 
  4. D
    Electrodynamic
Question 39Single Answer
A moving-coil galvanometer can be used as a DC ammeter by connecting
  1. A
    a high resistance in series with the meter
  2. B
    a high resistance across the meter
  3. C
    a low resistance across the meter
  4. D
    a low resistance in series with the meter
Question 40Single Answer
Consider the following types of damping:
1. Air-friction damping
2.Fluid-friction damping
3.Eddy-current damping
PMMC type instruments use which of the above?
  1. A
    1 only   
  2. B
    2 only
  3. C
    3 only 
  4. D
    1,2 and 3
Question 41Single Answer
In data acquisition system, analog data acquisition system is used
  1. A
    for narrow frequency width, while digital data acquisition system is used when wide frequency width is to be monitored
  2. B
    for wide frequency width, while digital data acquisition system is used when narrow frequency width is to be monitored
  3. C
    when quantity to be monitored varies slowly, while its counterpart is preferred if the quantity to be monitored varies very fast
  4. D
    when quantity to be monitored is time-variant, while digital data acquisition system is preferred when quantity is time invariant
Question 42Single Answer
During the measurement of resistance by Carey Foster bridge, no error is introduced due to
1.contact resistance
2. Connecting leads
3.thermoelectric e.m.f.
which of the above are correct?
  1. A
    1 and 2 only 
  2. B
    1 and 3 only
  3. C
    2 and 3 only 
  4. D
    1,2 and 3
Question 43Single Answer
Which of the following is true for the complete response of any network voltage or current variables for a step excitation to a first-order circuit?
  1. A
    It has the form at k1 e-at
  2. B
    It has the form k 
  3. C
    It may have either the form (a) or the form of (a) plus (b) 
  4. D
    It has the form e+at
Question 44Single Answer
A piezoelectric crystal has a coupling coefficient K of 0.32. How much electrical energy must be applied to produce output energy of 7.06 × 10–3 J?
  1. A
    25.38 mJ 
  2. B
    22.19 mJ 
  3. C
    4.80 mJ 
  4. D
    2.26 mJ 
Question 45Single Answer
A wattmeter reads 10 kW, when its current coil is connected in R phase and the potential coil is connected across R and neutral of a balanced 400 V (RYB sequence) supply. The line current is 54 A. If the potential coil reconnected across B-Y phases with the current coil in R phase, the new reading of the wattmeter will be nearly
  1. A
    10 kW 
  2. B
    13 kW
  3. C
    16 kW 
  4. D
    19 kW 
Question 46Single Answer
For a type-I system, the intersection of the initial slope of the Bode plot with 0dB axis gives
  1. A
    steady-state error
  2. B
    error constant
  3. C
    phase margin
  4. D
    cross-over frequency
Question 47Single Answer
The desirable features of a servomotor are
  1. A
    low rotor inertia and low bearing friction
  2. B
    high rotor inertia and high bearing friction.
  3. C
    low rotor inertia and high bearing friction
  4. D
    high rotor inertia low bearing friction
Question 48Single Answer
Permeance is inversely related to
  1. A
    resistance 
  2. B
    conductance
  3. C
    reluctance         
  4. D
    capacitance
Question 49Single Answer
Consider the following statements regarding an ideal core material:
1. It has very high permeability.
2. It loses all its magnetism when there is no current flow.
3. It does not saturate easily.
Which of the above statements are correct?
  1. A
    1 and 2 only 
  2. B
    1 and 3 only
  3. C
    2 and 3 only 
  4. D
    1, 2 and 3
Question 50Single Answer
The characteristic impedance of a transmission line depends upon
  1. A
    shape of the conductor
  2. B
    surface treatment of the conductor
  3. C
    conductivity of the material 
  4. D
    geometric configuration of the conductor
Important Questions Package

IMTECH Chandigarh Technician Exam Online Question Bank Package

Buy IMTECH Chandigarh Technician Important Questions, MCQ, question answer in Hindi & English. It will help you to score high marks in IMTECH Chandigarh Technician question bank 2026 in Online, PDF & Print study material.

+ Free Monthly Current Affairs, GK & more PDF Download
Sr.Package NameAmount
1.IMTECH Chandigarh Technical Assistant & Technician Exam Paper I - English
Description : 1000 Question with Answer 
₹181 [₹500]
2.IMTECH Chandigarh Technical Assistant & Technician Exam Paper I - Hindi
Description : 1000 Question with Answer
₹181 [₹500]
3.IMTECH Chandigarh Technical Assistant & Technician Exam Paper II - English
Description : 1000 Question with Answer
₹181 [₹500]
4.IMTECH Chandigarh Technical Assistant & Technician Exam Paper II - Hindi
Description : 1000 Question with Answer
₹181 [₹500]
5.IMTECH Chandigarh Technical Assistant Exam Paper III - English
Description : 1000 Question with Answer
₹181 [₹500]
6.IMTECH Chandigarh Technical Assistant Exam Paper III - Hindi
Description : 700 Question with Answer
₹181 [₹500]
7.IMTECH Chandigarh Technician Exam Paper III - English
Description : 1000 Question with Answer
₹181 [₹500]
8.MTECH Chandigarh Technician Exam Paper III - Hindi
Description : 700 Question with Answer
₹181 [₹500]
Back to Exam