Which of the following is the unit of kinematic viscosity _________________?

Consider the following processes:
1. Extension of a spring
2. Plastic deformation of a material
3. Magnetization of a material exhibiting hysteresis
Which of the above process are irreversible?

Which of the following statements are correct for a throttling process?
1. It is an adiabatic steady flow process
2. The enthalpy before and after throttling is same
3. In the processes, due to fall in pressure, the fluid velocity at outlet is always more than inlet velocity

A Reversed Carnot Engine removes 50 kW from a heat sink. The temperature of the heat sink is 250 K and the temperature of the heat reservoir is 300 K. The power required of the engine is

A heat engine receives heat at the rate of 2500 kJ/min and gives an output of 12.4 kW. Its thermal efficiency is, nearly

Consider the following motions :
1. Piston reciprocating inside an engine cylinder
2. Motion of a shaft between foot-step bearings
Which of the above can rightly be considered as successfully constrained motion?

A rotor weighing 2 kN is supported on bearings A and B which are 1 m apart. The centre of mass of the rotor is at a distance 0.4 m from bearing A. It is observed that there is an unbalanced couple of magnitude 300 N-m which leaves the shaft balanced statically.The dynamic reactions at the supports will be

A cam is a mechanical member used to impart a desired motion to a follower by direct contact. Which one of the under-listed follower motion types will produce the least jerk to the system?

In a circular are cam with a roller follower, acceleration of the follower depends on
1. cam speed and location of centre of circular arc
2. roller diameter and radius of circular arc
Which of the above is/are correct?

A manufacturing company is selling a product for 15 per unit with variable cost of  10 per unit. The fixed cost of the asset is 50,000. How many units should be produced to breakeven?

A spherical waterdrop of 1 mm in diameter splits up in air into 64 smaller drops of equal size. The surface tension coefficient of water in air is 0.073 N/m. The work required in splitting up the drop is

Consider the following statements pertaining to stability of floating bodies:
1. A floating body will be stable when the centre of gravity is above the centre of buoyancy.
2. The position of metacentres corresponding to different axes of rotation are generally different for the same floating object.
3. For cargo ships, the metacentric height varies with loading.
Which of the above statements are correct?

Water is coming out from a tap and falls vertically downwards. At the tap opening, the stream diameter is 20 mm with uniform velocity of 2 m/s. Assuming steady inviscid flow, constant pressure atmosphere everywhere, and neglecting curvature and surface tension effects, the diameter of the stream 0.5 m below the tap opening is nearly

Consider the following statements:
1. At low Reynolds numbers of any flow, viscous forces dominate over inertial forces.
2. Transition from laminar to turbulent flow occurs over a range of Reynolds numbers depending on the surface presented to the flow.
Which of the above statements is/are correct?

In a steady laminar flow of a given discharge through a circular pipe of diameter D, the head loss is proportional to

A fin will be more effective when Bio number is

A tank of length, breadth and height in the ratio of 2:1:2 is full of water. The ratio of hydrostatic force at the bottom to that at any larger vertical surface is

Which of the following fluids exhibit a certain shear stress at zero shear strain rate followed by a straight line relationship between shear stress and shear strain rate?

What is the specific gravity of a marble stone, which weighs 400N in air, and 200N in water? (g=10m/s²)

What is the intensity of pressure in the following SI units, when specific gravity of mercury is 13.6 and the intensity of pressure is 400KPa ?

Consider the following statements:
1.If a small upward displacement is given to a floating body, it results in the reduction of the buoyant force acting on the body
2.A slight horizontal displacement does not change either the magnitude or the location of the buoyant force 
Which of the above statements is/are correct? 

State whether following flow field is physically possible? 

In a differential manometer, a head of 0.5 m of fluid A in limb 1 is found to balance a head of 0.3 m of fluid B in limb 2. The atmospheric pressure is 760 mm of mercury. The ratio of specific gravities of A to B is

On which of the following just in time manufacturing philosophy emphasizes ?

In a stream line steady flow, two points A and B on a stream line are 1m apart and the flow velocity varies uniformly from 2m/s to 5m/s. What is the acceleration of fluid at B?

The stream function is given by Ψ = 3xy, then the velocity at the point (2,3) is

The boundary layer thickness at a given distance from the leading edge of a flat plate is

In a laminar flow through a circular pipe, the discharge varies

A fluid is flowing over a flat plate. At distance of 8 cm from the leading edge, the Reynolds number is found to be 25600. The thickness of the boundary layer at this point is

Air is flowing over a flat plate with a free stream velocity of 24 m/s, and its kinematic viscosity is 72 ×10^-6m²/s. If at a particular point, the Reynolds number is 30000, its location from the leading edge is

In a refrigerator, the evaporator and condenser coil temperatures are –33°C and 27°C, respectively. Assuming that the maximum COP is realized, the required power input for a refrigerating effect of 4 kW is
 

In a hydraulic coupling

Consider the following statements:
1.The wheel can be operated freely in air
2.Pressure at the exit of the nozzle is atmospheric
3.Pressure does not vary along the moving vanes
4.Change the direction of momentum imparts thrust over moving vanes Which of the following statements are applied to impulse turbine?

A water jet 0.0015m²in area issues from a nozzle with 15 m/s velocity. It is made to impinge perpendicular on to a plate that moves away from the jet with a velocity of 5 m/s. The force on the plate due to this impact is

Consider the following statements with regard to hydraulic turbines:
1.Kaplan turbines are most efficient at part load operations.
2.If n is the number of jets in a Pelton turbine, then the specific speed is proportional to n².
3.The flow ratio of Francis turbines are in the range of 0.1 – 0.3. 
Which of the above statements is/are correct? 

Which of the following is a Vector quantity ?

Bernoulli’s equation is applicable between any two points located in

Water flows through a smooth circular pipe of diameter D and length L because of a pressure difference ΔP across the length. The volume flow rate is Q and the flow is turbulent with Reynolds number 10⁵. If the pressure difference is increased to 4ΔP the volume flow rate will be

If a submerged body displaced from its equilibrium position, returns to its original position, it is called __________.

In a flow measurement, a venturi meter is preferred over an orifice plate because _____.

Pitot tube measures ______.

Which of the following is not a property of an ideal fluid ?

Nozzle used in steam turbines convert ________.

Which of the following assumptions is the most relevant in air-standard cycle analysis ?

The modern Francis turbine is a ___________flow turbine .

Variation of stress with strain rate for a Newtonian fluid is ______ .

Which of the following is NOT a part of refrigeration systems ?

Which of the following is NOT an intensive property ?