One bag of Portland cement, 50 kg in weight, would normally have a bulk volume of

AsCu, a preservative for wood, developed by the Forest Research Institute, Dehradun, comprises of chemicals:

Consider the following statements related to autoclave bricks:
1.Less water absorption compared to other bricks.
2.Noise reduction
3.It is cheap compared to other types of bricks.
4.Requirement of bulk volume of mortar in joints being relatively less compared to other types of brick masonry.
5.Not recommended for outer walls. 
Which of the above statements are relevant to the use of ‘autoclave’ bricks? 

The minimum number of annular rings to be seen in every 2.54 cm in the radial direction from the core for timber to be classified as ‘Dense’ is

If the actual thickness of a brick masonry wall is 19 cm, its effective length is 2.70 m, its effective height is 2.82 m and its code specified stiffening coefficient is 1.2 then, for design considerations, the slenderness ratio of the wall will be taken as

Consider the following forms of water in a hydrated cement paste:
1.Capillary water
2.Chemically combined water
3.Interlayer water
4.Adsorbed water 
Which of the above forms of water will, on its/their removal, cause shrinkage of the paste? 

Consider the following statements:High early strength of cement is obtained as a result of
1.Fine grinding.
2.Decreasing the lime content
3.Burning at higher temperature
4.Increasing the quality of gypsum. 
Which of the above statements are correct? 

Consider the following statements related to ‘composite mortar’:
1.Addition of lime to cement mortar improves its workability
2.Composite mortar is obtained by adding 10% by weight of cement and mixing with water.
3.Composite mortar is not preferred in tall buildings.
4.Mechanical grinding is essential for developing composite mortar.Which of the above statements are true in this case? 

Consider the following statements related to ‘non-destructive testing’ of concrete:
1.Indentation test is used to assess the quality of concrete.
2.Resonant Frequency Method is based on a laboratory test.
3.Compressive strength of concrete is estimated through Pulse Velocity Measurement.
4.Dynamic modulus of Elasticity is determined by a Sonometer Test.
5.Thickness of concrete can be estimated by in-situ Rebound Hammer Test. 
Which of the above statements are correct? 

What is the amount of water required for a workable RC of mix 1 : 2: 4 by weight., when W/C is 0-60 and unit weight of concrete is 2400 kg/m³?

Which IS code is used for classification of timber for seasoning purposes?

Consider the following with regard to the application of preservation of timber:
1.Increase in the life span of the member
2.Increase in the strength of the timber
3.Removal of moisture
4.Prevention of growth of fungi by killing them 
Which of the above are correct?

The plies in plywood are so placed that the grains of each ply are

Which of the following is an ODD one as regards ‘requirement of good brick-earth’?

The compressive strength of heavy-duty bricks, as per IS : 2980-1962, should not be less than

Consider the following statements:
1.Brickwork will have high water tightness.
2.Brickwork is preferred for monument structures.
3.Bricks resist fire better than stones
4.Bricks of good quality shall have thin mortar bonds. 
Which of the above statements are correct?

Consider the following statements:A good soil for making bricks should contain
1.30% alumina
2.10% lime nodules
3.Only small quantity of iron oxides
4.15% magnesia 
Which of the above statements are correct?

Which compound of cement is responsible for strength of cement?

Which type of cement is recommended in large mass concrete works such as a dam?

Consider the following statements regarding ‘setting of cement’:
1.Low-heat cement sets faster than OPC.
2.Final setting time decides the strength of cement
3.Initial setting time of Portland Pozzollona is 30 minutes
4.Air-induced setting is observed when stored under damp conditions.
4.Addition of gypsum retards the setting time. 
Which of the above statements are correct? 

Consider the following statements regarding ‘strength of cement’:
1.Strength test on cement is made on cubes of cement-sand mix.
2.Water to be used for the paste is 0.25 P, where P is the water needed for normal consistency.
3.The normal consistency is determined on Le Chatelier’s principle.
4.Cubes are cast in two layers in leak-proof moulds further compacted in each layer by vibration on a machine. 
Which of the above statements are correct? 

Which of the following ingredients refer to binding material of mortar?
1.Cement
2.Lime
3.Sand
4.Ashes 
Select the correct answer using the code given below. 

Consider the following statements:
1.Bricks in masonry are bound by mortar.
2.Mortars make brick damp-proof.
3.Strength of brick in masonry is improved by plastering.
4.Addition of lime improves workability.
5.Marine construction needs sulphate-resistant cement mortar. 
Which of the above statements are relevant for ‘cement mortar’? 

Consider the following parameters of concrete:
1.Impermeability
2.Compactness
3.Durability
4.Desired consistency
5.Workability 
Which of the above parameters are relevant for ‘water-cement ratio’? 

Consider the following statements:Presence of Na₂O and K₂O in concrete leads to
1.Expansive reaction in concrete
2.Cracking of concrete
3.Disruption of concrete
4.Shrinkage of concrete 
Which of the above statements are correct? 

The maximum total quantity of dry aggregate by mass per 50 kg of cement, to be taken as the sum of the individual masses of fine and coarse aggregates (kg), for M20 grade of concrete is

Absorption capacity of an aggregate refers to the difference expresses in appropriate proportion in water content between

Consider the following statements concerning  ‘elasticity of concrete’:
1.Stress-strain behavior of concrete is a straight line up to 10% ultimate stress.
2.Strain determination is obtained from tangent modulus.
3.Modulus of elasticity of concrete is also called as secant modulus. 
Which of the above statements are correct? 

Consider the following statements :The addition of CaCl₂ in concrete results in
1.Increased shrinkage
2.Decreased setting time
3.Decreased shrinkage
4.Increased setting time 
Which of the above statements are correct? 

Which of the following statements are correct ?
1.Knots in a tree affect the continuity of fibres.
2.Nail knots do not influence the strength of timber.
3.Druxiness of wood is not a defect.
4.Tall trees with twisted fibers give good timber for poles.

Excrescences in wood are
1.Defects found in trees
2.Formed due to injuries inflicted on trees when they are growing
3.Defects which render wood suitable as firewood only

What treatment is adopted for making timber fire-resistant?

Deterioration of structure of timber due to dry rot is:
1.Caused by fungi
2.Due to dry-spell after heavy rains
3.Due to attack of termites
4.ndicated by surface stripes on scantlings  

Alternate wetting and drying of timber :
1.Results in shrinkage and swelling
2.Brings about wet rot onset
3.Increases the durability
4.Causes transmission of spores from germination  

As per I.S. classification, the minimum compressive strength of a first class brick should be

When provided with alternating courses of (a) all headers and (b) all stretchers, the front elevation of such brick masonry is designated as

I.S. code specifies that the compressive strength of brick shall be determined by keeping the brick:
1.On edge
2.On bed
3.After soaking in water for 2 hrs
4.After soaking in water for 24 hrs  

Soundness test of cement is carried out to determine its

The objectives of producing cement include:
1.Incorporating industrial wastes
2.Increasing free lime
3.Increasing fineness
4.Saving energy needed in the process  

A mild steel rod tapers uniformly from 24 mm  mm dia. over its length of 400 mm. The rod when held vertical is subjected to an axial tensile load of 12 kN. E = 2 × 10⁵ N/mm². The extension of the rod in mm would be:

Two different liquids are flowing through different pipes of the same diameter. In the first pipe, the flow is laminar with centerline velocity,V_max.1,Whereas in the second pipe, the flow is turbulent. For turbulent flow, the average velocity is 0.82 times the centerline velocity,v_max.2 . For equal volumetric flow rates in both the pipes, the ratio V_max.1/V_max.2(up to two decimal place) is_____.
 

Poisson’s ratio of a material is 0.3. Then the ratio of Young’s modulus to bulk modulus is

For a gas phase cracking reaction A→B+C at 300℃ , the Gibbs free energy of the reaction at this temperature is ∆G°= -2750J/mol . The pressure is 1 bar and the gas phase can be assumed to be ideal. The universal gas constant =8.314J/mol. K. The fractional molar conversion of A at equilibrium is________.
 

Which of the following statements are correct ?
1.In a ductile material elastic deformation is more predominant than plastic one.
2.Brittleness is not an absolute property of a metal.
3.Rate of loading has no influence in changing the behavior of a metal from ‘ductile’ to ‘brittle’ at low temperatures
4.Under hydrostatic compression, a brittle metal may change into a ductile one. 

The total deflection of a structure when subjected simultaneously to different sets of loading is equal to the sum of the deflections under each such set of loads as if acting separately on the structure. Which one the following justifies this statement?

A rectangular bar of cross-sectional area a is subjected to an axial tensile load P. The maximum shear stress will occur on a plane at X° to any normal cross-section where X° is

A solid circular shaft has been subjected to a pure torsion moment. The ratio of maximum shear stress to maximum normal stress at any point would be

Which of the following statements are correct?
1.All load carrying members transmit load through basic modes of tension, compression, torsion and shear only.
2.Beams carry transverse loads.
3.Combined loading is a complicated loading.
4.Nature of internal forces decides the aspect of combines loading. 

Identify the WRONG statement amongst the following:

Which of the following statements are correct?
1.Experimental results on thin-walled tubes show that maximum normal stress theory is valid.
2.Normal-stress theory is valid in case of brittle materials.
3.In case of pure shear, St. Venant’s theory is more valid than other theories.
4.Tresca’s theory is very closely substantiated by experimental results.
5.In maximum stress theory, the yield locus is a hexagon.