Question for OPTCL Junior Management Trainee 2026 - Quiz / Questions / MCQ

Objective Questions

Latest OPTCL JMT Exam Question (Objective Questions), MCQ in English

Subjects : Civil, Numerical, GK & Reasoning, English Knowledge

Question Bank OPTCL Junior Management Trainee (Civil) Exam - English

Back to Exam

Civil

Question 1Single Answer

A water supply distribution system for an averagely-populated township is to be designed for

A
Maximum daily demand
B
Maximum hourly demand and fire demand
C
Average demand
D
Maximum daily demand and fire demand or maximum hourly demand, whichever is higher

Question 2Single Answer

A combined sewerage system is more appropriate for developed areas where

A
Rainfall occurs for a very few days in a year
B
Rainfall occurs almost uniformly throughout the year
C
Air temperatures are nearly uniform throughout the year
D
Air temperatures through the year include extremes during certain runs of days

Question 3Single Answer

100 m³ of sludge holds a moisture content of 95%. If its moisture content chagnes to 90%, the volume of this sludge will then be

A
40.5m³
B
50m³
C
75m³
D
94.7m³

Question 4Single Answer

The design overflow rate of a sedimentation tank is chosen considering

A
Flow rate through the tank
B
Diameter of the particle intended to be removed
C
Volume of the sedimentation tank
D
Detention time in the tank

Question 5Single Answer

Consider the following statements in respect of flow equalization in a waste water treatment plant :
1. Biological treatment is enhanced because shock loadings are eliminated or minimized
2. Flow equalizations is an attractive option for upgrading the performance of overloaded treatment plants.
3. Inhibiting substances can be diluted and pH can be stabilized
4. Thickening performance of primary sedimentation tanks following grit removal is improved.
Which of the above statements are correct?

A
1, 2, 3 and 4
B
1, 2 and 3 only
C
1, 2 and 4 only
D
3 and 4 only

Question 6Single Answer

A drain carrying 5m³/s of wastewater with its BOD of 100mg/l joins a stream carrying 50 m³/ s flow with its BOD of 5mg/l. What will be the value of the BOD of the combined flow after complete mixing?

A
3.6 mg/l
B
13.6 mg/l
C
33.6 mg/l
D
53.6 mg/l

Question 7Single Answer

Consider the following statements :
1. There will be no defects in select grade timbers.
2. The codal values for strength of grade-II timer without defects may be reduced by 37.5%.
3. For timber used as columns, the permissible stress in ungraded timbers is adopted with a multiplying factor of 0.50.
4. In case of wind force and earthquakes, a modification factor of 1.33 is adopted. Which of the above statements are correct ?

A
1 and 3 only
B
1 and 4 only
C
2 and 4 only
D
2 and 3 only

Question 8Single Answer

Consider the following statements regarding timber :
1. The strength of timber increases by Kiln seasoning.
2. Cutting of wood is to be done prior to treatment.
3. Water seasoning is good for prevention of warping.
4. ASCU treatment enhances the strength of wood. Which of the above statements are correct ?

A
1, 2 and 3 only
B
2, 3 and 4 only
C
1, 3 and 4 only
D
1, 2, 3 and 4

Question 9Single Answer

Gase(s) emitted during rotting or decomposition of timber is /are mainly

A
Methane and Hydrogen
B
Hydrogen Sulphide
C
Carbonic acid and Hydrogen
D
Ammonia

Question 10Single Answer

Efflorescence of bricks is due to

A
Excessive burning of bricks
B
High silt content in brick clay
C
High porosity of bricks
D
Soluble salts present in parent clay

Question 11Single Answer

Disintegration of bricks masonry walls is primarily due to
1. Efflorescence
2. Magnesium sulphate in brick
3. Calcined clay admixtures
4. Kankar nodules
Which of the a above statements are correct ?

A
1, 2 and 3 only
B
1, 2 and 4 only
C
3 and 4 only
D
1, 2, 3 and 4

Question 12Single Answer

Consider the following test :
1. Transverse strength test
2. Water absorption test
3. Impact test
4. Breaking strength test
Which of the above are relevant to testing of tiles ?

A
1, 2 and 3 only
B
1, 2 and 4 only
C
3 and 4 only
D
1, 2, 3 and 4

Question 13Single Answer

Which of the following statements is/are correct regarding the strength of cement ?
1. Particle sizes less than 3 m increases the viscous nature of the cement.
2. Finer particles in cement can be replaced by fly-ash to improve the strength.

A
1 only
B
2 only
C
Both 1 and 2
D
Neither 1 nor 2

Question 14Single Answer

Consider the following statements:
1. IS 3583 refers to Burnt Clay Paving Bricks.
2. IS 5779 refers to Burnt Clay Soling Bricks.
3. IS 3952 refers to Burnt Clay Hollow Bricks.
4. IS 2222 refers to Burnt Clay Lay Bricks.
Which of the above statements are correct?

A
1, 2 and 3 only
B
1, 2 and 4 only
C
3 and 4 only
D
1, 2, 3 and 4

Question 15Single Answer

Consider the following statements:
1. A high aggregate impact value indicates strong aggregates.
2. A low aggregate crushing value indicates high crushing strength of aggregates.
3. Aggregates having elongation index values greater than 15% are generally considered suitable for pavement construction.
4. Flakiness index of aggregates should not be less than 25% for use in road construction.
Which of the above statements are correct?

A
2 and 3 only
B
2 and 4 only
C
1 and 3 only
D
1 and 4 only

Question 16Single Answer

Consider the following statements regarding refractory bricks in furnaces:
1. The furnace is fired at temperatures more than 1700°C.
2. Silica content in the soil should be less than 40%.
3. Water absorption of bricks should not exceed 10%
4. Chrome bricks are known as basic bricks. Which of the above statements are correct?

A
1 and 2 only
B
2 and 4 only
C
1 and 3 only
D
3 and 4 only

Question 17Single Answer

Consider the following statements about lime:
1. Calcination of limestone results in quick lime.
2. Lime produced from pure variety of chalk is hydraulic lime.
3. Hydrated lime is obtained by treating quick lime with water.
Which of the above statements are correct?

A
1, 2 and 3
B
1 and 2 only
C
2 and 3 only
D
1 and 3 only

Question 18Single Answer

Consider the following statements:
1. If more water is added to concrete for increasing its workability, it results into concrete of low strength.
2. No slump is an indication of a good workable concrete.
3. Higher the slump of concrete, lower will be its workability.
4. Workability of concrete is affected by water content as well as water-cement ratio.
Which of the above statements are correct?

A
1 and 3 only
B
2 and 3 only
C
1 and 4 only
D
2 and 4 only

Question 19Single Answer

Pozzolana used as an admixture in concrete has the following advantages:
1. It improves workability with lesser amount of water.
2. It increases the heat of hydration and so lets the concrete set quickly.
3. It increases the resistance of concrete to attack by salts and sulphates.
4. It leaches out calcium hydroxide.
Select the correct answer using the codes given below:

A
1, 2 and 3 only
B
1, 2 and 4 only
C
1, 3 and 4 only
D
2, 3 and 4 only

Question 20Single Answer

Consider the following statements regarding Cyclopean Concrete:
1. Size of aggregate is more than 150 mm.
2. Size of aggregate is less than 150 mm.
3. High slump.
4. High temperature rise due to heat of hydration.
Which of the above statements are correct?

A
1 and 3 only
B
1 and 4 only
C
2 and 3 only
D
2 and 4 only

Question 21Single Answer

One bag of Portland cement, 50 kg in weight, would normally have a bulk volume of

A
30 l
B
35 l
C
40 l
D
45 l

Question 22Single Answer

AsCu, a preservative for wood, developed by the Forest Research Institute, Dehradun, comprises of chemicals:

A
1 : 1 : 1
B
1 : 2 : 3
C
1 : 2 : 4
D
1 : 3 : 4

Question 23Single Answer

Consider the following statements related to autoclave bricks:
1.Less water absorption compared to other bricks.
2.Noise reduction
3.It is cheap compared to other types of bricks.
4.Requirement of bulk volume of mortar in joints being relatively less compared to other types of brick masonry.
5.Not recommended for outer walls.
Which of the above statements are relevant to the use of ‘autoclave’ bricks?

A
1, 2 and 4
B
1, 3 and 5
C
2, 3 and 4
D
2, 4 and 5

Question 24Single Answer

The minimum number of annular rings to be seen in every 2.54 cm in the radial direction from the core for timber to be classified as ‘Dense’ is

A
10
B
20
C
25
D
30

Question 25Single Answer

If the actual thickness of a brick masonry wall is 19 cm, its effective length is 2.70 m, its effective height is 2.82 m and its code specified stiffening coefficient is 1.2 then, for design considerations, the slenderness ratio of the wall will be taken as

A
11.8
B
12.4
C
14.2
D
14.8

Question 26Single Answer

Consider the following forms of water in a hydrated cement paste:
1.Capillary water
2.Chemically combined water
3.Interlayer water
4.Adsorbed water
Which of the above forms of water will, on its/their removal, cause shrinkage of the paste?

A
1, 2 and 3
B
1, 2 and 4
C
2, 3 and 4
D
1, 3 and 4

Question 27Single Answer

Consider the following statements:High early strength of cement is obtained as a result of
1.Fine grinding.
2.Decreasing the lime content
3.Burning at higher temperature
4.Increasing the quality of gypsum.
Which of the above statements are correct?

A
1 and 2
B
1 and 3
C
2 and 3
D
3 and 4

Question 28Single Answer

Consider the following statements related to ‘composite mortar’:
1.Addition of lime to cement mortar improves its workability
2.Composite mortar is obtained by adding 10% by weight of cement and mixing with water.
3.Composite mortar is not preferred in tall buildings.
4.Mechanical grinding is essential for developing composite mortar.Which of the above statements are true in this case?

A
1, 2 and 3 only
B
1, 3 and 4 only
C
2, 3 and 4 only
D
1, 2, 3 and 4

Question 29Single Answer

Consider the following statements related to ‘non-destructive testing’ of concrete:
1.Indentation test is used to assess the quality of concrete.
2.Resonant Frequency Method is based on a laboratory test.
3.Compressive strength of concrete is estimated through Pulse Velocity Measurement.
4.Dynamic modulus of Elasticity is determined by a Sonometer Test.
5.Thickness of concrete can be estimated by in-situ Rebound Hammer Test.
Which of the above statements are correct?

A
1, 2 and 3 only
B
1, 2 and 5 only
C
1, 2, 3 and 4 only
D
1, 2, 3, 4 and 5

Question 30Single Answer

What is the amount of water required for a workable RC of mix 1 : 2: 4 by weight., when W/C is 0-60 and unit weight of concrete is 2400 kg/m³?

A
165 l
B
205 l
C
245 l
D
285 l

Question 31Single Answer

Which IS code is used for classification of timber for seasoning purposes?

A
IS : 4970-1973
B
IS : 1708-1969
C
IS : 1141-1958
D
IS : 399-1963

Question 32Single Answer

Consider the following with regard to the application of preservation of timber:
1.Increase in the life span of the member
2.Increase in the strength of the timber
3.Removal of moisture
4.Prevention of growth of fungi by killing them
Which of the above are correct?

A
1, 2, 3 and 4
B
2 and 4 only
C
1 and 4 only
D
2 and 3 only

Question 33Single Answer

The plies in plywood are so placed that the grains of each ply are

A
Parallel to each other
B
At right angle to one another
C
45° oblique to adjacent grain
D
Not constrained by any consideration

Question 34Single Answer

Which of the following is an ODD one as regards ‘requirement of good brick-earth’?

A
It must be free from lumps of lime
B
It should not be mixed with salty water
C
It must be non-homogeneous
D
It should not contain vegetable and organic matter

Question 35Single Answer

The compressive strength of heavy-duty bricks, as per IS : 2980-1962, should not be less than

A
440 kg/cm²
B
175 kg/cm²
C
100kg/cm²
D
75kg/cm²

Question 36Single Answer

Consider the following statements:
1.Brickwork will have high water tightness.
2.Brickwork is preferred for monument structures.
3.Bricks resist fire better than stones
4.Bricks of good quality shall have thin mortar bonds.
Which of the above statements are correct?

A
1 and 2
B
3 and 4
C
2 and 3
D
1 and 4

Question 37Single Answer

Consider the following statements:A good soil for making bricks should contain
1.30% alumina
2.10% lime nodules
3.Only small quantity of iron oxides
4.15% magnesia
Which of the above statements are correct?

A
1 and 2 only
B
1 and 3
C
1, 2 and 4
D
2, 3 and 4

Question 38Single Answer

Which compound of cement is responsible for strength of cement?

A
Magnesium oxide
B
Silica
C
Alumina
D
Calcium sulphate

Question 39Single Answer

Which type of cement is recommended in large mass concrete works such as a dam?

A
Ordinary Portland
B
High Alumina
C
Low-heat Portland
D
Portland Cement

Question 40Single Answer

Consider the following statements regarding ‘setting of cement’:
1.Low-heat cement sets faster than OPC.
2.Final setting time decides the strength of cement
3.Initial setting time of Portland Pozzollona is 30 minutes
4.Air-induced setting is observed when stored under damp conditions.
4.Addition of gypsum retards the setting time.
Which of the above statements are correct?

A
1, 2 and 3
B
2, 3 and 4
C
3, 4 and 5
D
2, 3 and 5

Question 41Single Answer

Consider the following statements regarding ‘strength of cement’:
1.Strength test on cement is made on cubes of cement-sand mix.
2.Water to be used for the paste is 0.25 P, where P is the water needed for normal consistency.
3.The normal consistency is determined on Le Chatelier’s principle.
4.Cubes are cast in two layers in leak-proof moulds further compacted in each layer by vibration on a machine.
Which of the above statements are correct?

A
1 and 2
B
2 and 3
C
1 and 4
D
3 and 4

Question 42Single Answer

Which of the following ingredients refer to binding material of mortar?
1.Cement
2.Lime
3.Sand
4.Ashes
Select the correct answer using the code given below.

A
1 and 4
B
3 and 4
C
1 and 2
D
2 and 3

Question 43Single Answer

Consider the following statements:
1.Bricks in masonry are bound by mortar.
2.Mortars make brick damp-proof.
3.Strength of brick in masonry is improved by plastering.
4.Addition of lime improves workability.
5.Marine construction needs sulphate-resistant cement mortar.
Which of the above statements are relevant for ‘cement mortar’?

A
1, 2 and 3
B
2, 3 and 4
C
1, 4 and 5
D
3, 4 and 5

Question 44Single Answer

Consider the following parameters of concrete:
1.Impermeability
2.Compactness
3.Durability
4.Desired consistency
5.Workability
Which of the above parameters are relevant for ‘water-cement ratio’?

A
4 and 5
B
1 and 2
C
2 and 4
D
3 and 5

Question 45Single Answer

Consider the following statements:Presence of Na₂O and K₂O in concrete leads to
1.Expansive reaction in concrete
2.Cracking of concrete
3.Disruption of concrete
4.Shrinkage of concrete
Which of the above statements are correct?

A
1 and 2 only
B
2 and 3 only
C
1, 2 and 3
D
3 and 4

Question 46Single Answer

The maximum total quantity of dry aggregate by mass per 50 kg of cement, to be taken as the sum of the individual masses of fine and coarse aggregates (kg), for M20 grade of concrete is

A
625
B
480
C
330
D
250

Question 47Single Answer

Absorption capacity of an aggregate refers to the difference expresses in appropriate proportion in water content between

A
A wet aggregate and a dry aggregate
B
A dry aggregate and a wet aggregate
C
A saturated surface-dry aggregate and a dry aggregate
D
A saturated surface-dry aggregate and an over dry aggregate

Question 48Single Answer

Consider the following statements concerning ‘elasticity of concrete’:
1.Stress-strain behavior of concrete is a straight line up to 10% ultimate stress.
2.Strain determination is obtained from tangent modulus.
3.Modulus of elasticity of concrete is also called as secant modulus.
Which of the above statements are correct?

A
1, 2 and 3
B
1 and 3 only
C
1 and 2 only
D
2 and 3 only

Question 49Single Answer

Consider the following statements :The addition of CaCl₂ in concrete results in
1.Increased shrinkage
2.Decreased setting time
3.Decreased shrinkage
4.Increased setting time
Which of the above statements are correct?

A
1 only
B
2 and 3
C
3 and 4
D
1 and 2

Question 50Single Answer

Which of the following statements are correct ?
1.Knots in a tree affect the continuity of fibres.
2.Nail knots do not influence the strength of timber.
3.Druxiness of wood is not a defect.
4.Tall trees with twisted fibers give good timber for poles.

A
1, 2, 3 and 4
B
1, 2 and 4 only
C
1, 2 and 3 only
D
2, 3 and 4 only

Important Questions Package

OPTCL JMT Exam Online Question Bank Package

Buy OPTCL JMT Important Questions, MCQ, question answer in Hindi & English. It will help you to score high marks in OPTCL JMT question bank 2026 in Online, PDF & Print study material.

+ Free Monthly Current Affairs, GK & more PDF Download

Sr.	Package Name	Amount
1.	OPTCL Junior Management Trainee (Civil) Exam - English Description : 1000 Question with Answer	₹101 ~~[₹500]~~
2.	OPTCL Junior Management Trainee (Civil) Exam - English Description : 2000 Question with Answer	₹151 ~~[₹500]~~
3.	OPTCL Junior Management Trainee (Civil) Exam - English Description : 1000 Question & Answer Download in PDF (Send by Email)	₹151 ~~[₹450]~~
4.	OPTCL Junior Management Trainee (Civil) Exam Question Bank Book - English Description : 1000 Question with Answer (Printed Material)	₹390 ~~[₹600]~~
5.	OPTCL Junior Management Trainee Exam (Electrical) - English (Old) Description : 1000 Question witrh Answer	₹101 ~~[₹500]~~

Civil

Question 51Single Answer

Excrescences in wood are
1.Defects found in trees
2.Formed due to injuries inflicted on trees when they are growing
3.Defects which render wood suitable as firewood only

A
1, 2 and 3
B
1 and 2 only
C
1 and 3 only
D
2 and 3 only

Question 52Single Answer

What treatment is adopted for making timber fire-resistant?

A
ASCU treatment
B
Abel’s process
C
Creosoting
D
Tarring

Question 53Single Answer

Deterioration of structure of timber due to dry rot is:
1.Caused by fungi
2.Due to dry-spell after heavy rains
3.Due to attack of termites
4.ndicated by surface stripes on scantlings

A
1 and 2
B
3 and 4
C
2 and 3
D
1 and 4

Question 54Single Answer

Alternate wetting and drying of timber :
1.Results in shrinkage and swelling
2.Brings about wet rot onset
3.Increases the durability
4.Causes transmission of spores from germination

A
1, 2, 3 and 4
B
1, 2 and 4 only
C
1, 2 and 3 only
D
2, 3 and 4 only

Question 55Single Answer

As per I.S. classification, the minimum compressive strength of a first class brick should be

A
75 kg/cm³
B
100kg/cm³
C
125 kg/cm³
D
150 kg/cm³

Question 56Single Answer

When provided with alternating courses of (a) all headers and (b) all stretchers, the front elevation of such brick masonry is designated as

A
English bond
B
Single Flemish bond
C
Double Flemish bond
D
Rat-trap bond

Question 57Single Answer

I.S. code specifies that the compressive strength of brick shall be determined by keeping the brick:
1.On edge
2.On bed
3.After soaking in water for 2 hrs
4.After soaking in water for 24 hrs

A
1 and 2
B
2 and 3
C
3 and 4
D
2 and 4

Question 58Single Answer

Soundness test of cement is carried out to determine its

A
Alumina content
B
Iron oxide content
C
Free lime content
D
Durability under sea water

Question 59Single Answer

The objectives of producing cement include:
1.Incorporating industrial wastes
2.Increasing free lime
3.Increasing fineness
4.Saving energy needed in the process

A
1, 2, 3 and 4
B
1, 3 and 4 only
C
1, 2 and 4 only
D
2, 3 and 4 only

Question 60Single Answer

A mild steel rod tapers uniformly from 24 mm mm dia. over its length of 400 mm. The rod when held vertical is subjected to an axial tensile load of 12 kN. E = 2 × 10⁵ N/mm². The extension of the rod in mm would be:

A
3
2
B
2
3
C
3
D
1
3

Question 61Single Answer

Two different liquids are flowing through different pipes of the same diameter. In the first pipe, the flow is laminar with centerline velocity,V_max.1,Whereas in the second pipe, the flow is turbulent. For turbulent flow, the average velocity is 0.82 times the centerline velocity,v_max.2 . For equal volumetric flow rates in both the pipes, the ratio V_max.1/V_max.2(up to two decimal place) is_____.

A
1.64
B
2.45
C
0.25
D
1.44

Question 62Single Answer

Poisson’s ratio of a material is 0.3. Then the ratio of Young’s modulus to bulk modulus is

A
0.6
B
0.8
C
1.2
D
1.4

Question 63Single Answer

For a gas phase cracking reaction A→B+C at 300℃ , the Gibbs free energy of the reaction at this temperature is ∆G°= -2750J/mol . The pressure is 1 bar and the gas phase can be assumed to be ideal. The universal gas constant =8.314J/mol. K. The fractional molar conversion of A at equilibrium is________.

A
0.44
B
0.50
C
0.64
D
0.80

Question 64Single Answer

Which of the following statements are correct ?
1.In a ductile material elastic deformation is more predominant than plastic one.
2.Brittleness is not an absolute property of a metal.
3.Rate of loading has no influence in changing the behavior of a metal from ‘ductile’ to ‘brittle’ at low temperatures
4.Under hydrostatic compression, a brittle metal may change into a ductile one.

A
1 and 2
B
2 and 3
C
3 and 4
D
2 and 4

Question 65Single Answer

The total deflection of a structure when subjected simultaneously to different sets of loading is equal to the sum of the deflections under each such set of loads as if acting separately on the structure. Which one the following justifies this statement?

A
Elastic limit is not exceeded
B
Elastic limit including buckling is not exceeded
C
Limit state is not exceeded
D
Proportional limit without buckling is not exceeded

Question 66Single Answer

A rectangular bar of cross-sectional area a is subjected to an axial tensile load P. The maximum shear stress will occur on a plane at X° to any normal cross-section where X° is

A
90°
B
27°
C
180°
D
45°

Question 67Single Answer

A solid circular shaft has been subjected to a pure torsion moment. The ratio of maximum shear stress to maximum normal stress at any point would be

A
1 : 2
B
1 : 1
C
2 : 3
D
2 : 1

Question 68Single Answer

Which of the following statements are correct?
1.All load carrying members transmit load through basic modes of tension, compression, torsion and shear only.
2.Beams carry transverse loads.
3.Combined loading is a complicated loading.
4.Nature of internal forces decides the aspect of combines loading.

A
1 and 2
B
2 and 3
C
3 and 4
D
2 and 4

Question 69Single Answer

Identify the WRONG statement amongst the following:

A
steam distillation is used for mixtures that re immiscible with water.
B
Vacuum distillation is used for mixtures that are miscible with water.
C
Steam distillation is used for mixtures that are miscible with water.
D
vacuum distillation columns have larger diameter as compared to atmospheric columns for the same throughout

Question 70Single Answer

Which of the following statements are correct?
1.Experimental results on thin-walled tubes show that maximum normal stress theory is valid.
2.Normal-stress theory is valid in case of brittle materials.
3.In case of pure shear, St. Venant’s theory is more valid than other theories.
4.Tresca’s theory is very closely substantiated by experimental results.
5.In maximum stress theory, the yield locus is a hexagon.

A
1, 2 and 3
B
2, 4 and 5
C
1, 2 and 4
D
2, 3 and 4

Question 71Single Answer

What will be the depth of penetration of the plunger in Vicat Apparatus (IS : 5513 - 1976) from the bottom of the Vicat Mould, when the cement paste is tested for standard consistency, according to IS 4031 – 1988 ?

A
11 to 15 mm
B
8 to 10 mm
C
15 to 17 mm
D
5 to 7 mm

Question 72Single Answer

Two sewer pipelines A and B (having the same diameter and made of the same material) are laid at a bed slope of 1 in 225 and 1 in 625, respectively. Determine the ratio of their carrying capacities (Q_A to Q_B) .

Question 73Single Answer

Select the correct statement with respect to an over - reinforced cement concrete section under the working stress method .

A
The compressive stress in steel reaches the allowable limit before the maximum tensile stress in concrete reaches the allowable limit
B
Tensile steel stress and maximum compressive stress in concrete simultaneously reach their allowable limits
C
The allowable limiting stress is reached in concrete before the steel stress reaches the limiting value
D
The tensile stress in steel reaches the allowable limit before the maximum compressive stress in concrete reaches the allowable limit

Question 74Single Answer

A cantilever beam of span L is built - in at the support. It is restrained against lateral deflection and torsion at the free end. The effective length of compression flange for the beam as per IS 800 : 2007 is

A
0.5 L
B
0.85 L
C
2 L
D
0.75 L

Question 75Single Answer

What is the principle of plane surveying ?

A
Working from part to whole
B
Working from point to area
C
Working from angle to volume
D
Working from whole to part

Question 76Single Answer

According is IS 5968 : 1987, the minimum radius of radius of curve to be provided in the alignment of unlined canals carrying a discharge of less than 30 cumecs up to 15 cumecs is :

A
100 m
B
1000 m
C
600 m
D
150 m

Question 77Single Answer

A Pelton wheel is to be designed for a pitch diameter of 1 m and jet diameter of 0.1 m. The number of buckets on the runner computed by Taygun’s formula is :

A
20
B
25
C
15
D
10

Question 78Single Answer

What is the effect of fly ash in concrete ?

A
Reduces the secondary hydration process
B
Increases the heat of hydration
C
Increases the amount of air entrainment
D
Reduces the heat of hydration

Question 79Single Answer

As per IS 456 : 2000, the minimum grade of concrete to be used for plain concrete and reinforced concrete, respectively, in concrete works exposed directly along the sea coast are :

A
M 20 and M 30
B
M 20 and M 25
C
M 22 and M 40
D
M 15 and M 25

Question 80Single Answer

Identify the property that changes as a function of the geometrical dimensions of a section in structural materials :

A
Mass density
B
Moment of inertia
C
Poission’s ratio
D
Modulus of elasticity

Question 81Single Answer

As per IRC (Indian Roads Congress) recommendation, what will be the designed stopping sight distance (in metres) at the vehicle speed of 80 km/h on a rural highway ?

A
120
B
140
C
70
D
60

Question 82Single Answer

No deduction is made in the quantity estimation for plastering work in cement mortar for openings having size up to :

A
0.5 m²
B
1.0 m²
C
3 m²
D
0.75 m²

Question 83Single Answer

What is the height of slump cone mould used for testing the workability of the concrete ?

A
20 cm
B
10 cm
C
30 cm
D
25 cm

Question 84Single Answer

Select the correct option with regard in the following statements (S1, S2) pertaining to pavements .
S1 : Present serviceability index is used for the functional evaluation of pavement surface condition
S2 : Rigid pavements are less affected by temperature variations than flexible pavements

A
Statements S1 is true and Statement S2 is false
B
Both statements S1 and S2 are false
C
Statements S1 is false and Statement S2 is true
D
Both statements S1 and S2 are true

Question 85Single Answer

If the quadrantal bearing of a line AB is S 31'35' E, then its whole circle bearing is equal in :

A
121^o25'
B
148^o25'
C
58^o25'
D
211^o25'

Question 86Single Answer

The overflowing sheet of water on a weir is called :

A
creek
B
crest
C
limp
D
nappe

Question 87Single Answer

According to IS 456 - 2000, what is the slump of a medium degree of workability of concrete if planed in heavily reinforced sections like slabs, beams, walls, columns ?

A
10 - 25 mm
B
25 - 50 mm
C
0 - 10 mm
D
50 - 100 mm

Question 88Single Answer

Which of the following is Kharif season in India ?

A
March / April to June / July
B
December / January to April / May
C
May / June to October / November
D
October / November to April / May

Question 89Single Answer

The estimated value of a built - up property at the end of its useful life without dismantled is called :

A
market value
B
book value
C
scrap value
D
salvage value

Question 90Single Answer

The amount of cement required for 100 m²area, of damp proof course with 2.5 cm thinkness, in with proportion of 1: 2 : 4 (cement : sand : aggregate) will be :

A
2.5 m²
B
0.55 m²
C
1.10 m²
D
0.25 m²

Question 91Single Answer

Select the correct statement related to increasing the carbon content in steel from 0.2 to 0.9 percent .

A
Increasing the carbon content in steel decreases the yield stress and increases the ductility
B
Increasing the carbon content in steel increases the yield stress and reduces the ductility
C
Increasing the carbon content in steel decreases the yield stress and does not affect the ductility
D
Increasing the carbon content in steel does not have any effect on the yield stress or ductility

Question 92Single Answer

Which of the following laws states that pressure or intensity of pressure at a point is static fluid is equal in all directions ?

A
Newton's law
B
Pascal's law
C
Darcy's law
D
Hydrostatic law

Question 93Single Answer

The determination of plasticity index and the percentage by weight of clay mineral finer than 2 µ present in the soil were done for two soil samples A and B. The ratio of plasticity index to the percentage of clay size particle for the samples A and B are given in the table .
Soil sample Ratio of plasticity index to percentage of clay size particle
Sample A Less than 0.75
Sample B Greater than 1.25 The two soil sample A and B are classified as

A
Sample A : Inactive; Sample B : Active
B
Sample A : Active; Sample B : Normal
C
Sample A : Active; Sample B : Inactive
D
Sample A : Normal ; Sample B : Inactive

Question 94Single Answer

Which of the following compounds of cement is responsible for early strength ?

A
C₄AF
B
C₃S
C
C₃A
D
C₂A

Question 95Single Answer

According to SP : 27 - 1984, the thickness of slab or RC slab shall be measured to the nearest of :

A
0.0002 m
B
0.005 m
C
0.0001 m
D
0.01 m

Question 96Single Answer

Classify the following pollutants as primary pollutants (PP) and secondary pollutants (SP). Ozone, Carbon monoxide, Particulate matter, photochemical smog, Nitrogen oxides, Aerosol/mist, Hydrocarbons, Perory - Acetyl - Nitrate, Sulphur dioxide.

A
PP : Ozone, Photochemical smog, Aerosol/mist, Peroxy – Acetyl - Nitrate
SP : Carbon monoxide, Particulate matter, Nitrogen oxides, Hydrocarbons, Sulphur dioxide
B
SP : Carbon monoxide, Particulate matter, Aerosol/mist, Peroxy - Acetyl - Nitrate
SP : Nitrogen oxides, Hydrocarbons, Sulphur dioxide, Ozone, Photochemical smog
C
PP : Carbon monoxide, Particulate matter, Hydrocarbons, Sulphur dioxide
SP : Ozone, Photochemical smog, Aerosol/mist, Peroxy - Acetyl - Nitrate
D
PP : Ozone, Photochemical smog, Carbon monoxide, Particulate matter, Nitrogen oxides
SP : Aerosol/mist, Peroxy - Acetyl - Nitrate, Hydrocarbons, Sulphur dioxide

Question 97Single Answer

Saturated unit weight of soil is the ratio of :

A
bulk unit weight of a soil when it is fully saturated
B
saturated bulk unit weight to total void
C
total void to saturated bulk unit weight
D
total void to saturated bulk unit weight

Question 98Single Answer

Identify the test to be conducted for the determination of the modulus of subgrade reaction in pavement design .

A
Plate bearing test
B
Triaxial test
C
CBR test
D
Direct shear test

Question 99Single Answer

In limit state design, the design bond stress for deformed bars (conforming to IS 1786) for M20 concrete mentioned in IS 456 : 2000 is (in N/mm² units) :

A
1.2
B
1.8
C
1.68
D
1.92

Question 100Single Answer

Which of the following can be considered as a taking off point in road planning in India ?

A
Lucknow plan
B
Delhi plan
C
Bombay plan
D
Nagpur plan

Question 101Single Answer

The following two statements pertain to a simply supported under reinforced concrete beam. Select the correct option with regard is these statements .
1. The failure of the beam takes place due to the yielding of steel .
2. The moment of resistance of the beam is more than that of the balanced section of the beam .

A
Statement 1 is true but Statement 2 is false
B
Statement 1 is false but Statement 2 is true
C
Both statement 1 and 2 are true
D
Both statement 1 and 2 are false

Question 102Single Answer

A continuous beam ABC with span AB = BC = L is shown in the figure. Support A is fixed type, and supports B and C are roller type. The kinematic indeterminacy of the beam is :

Question 103Single Answer

The soils transported and deposited by a river or a stream care called :

A
aeolian soils
B
alluvial soils
C
lacustrine soils
D
marine soils

Question 104Single Answer

What is the mechanical extra widening required for a two-lane pavement of width 7 m on a horizontal curve of radius 250 m, if the longest wheel base of a vehicle expected on the road is 5 m with a design speed of 70 km/h ?

A
0.155 m
B
0.225 m
C
0.100 m
D
0.552 m

Question 105Single Answer

The following are some of the errors that area associated with a total station survey work. Vertical collimation error, Centering error, Horizontal collimation error, Eccentricity error Categorize the given errors as those due to temporary adjustments (T) and permanent adjustments (P).

A
T : Vertical collimation error, Horizontal collimation error
P : Centering error, Eccentricity error
B
T : Centering error, Horizontal collimation error, Eccentricity error
P : Vertical collimation error
C
T : Eccentricity error, Horizontal collimation error
P : Centering error, Vertical collimation error, Eccentricity error
D
T : Centering error
P : Vertical collimation error, Horizontal collimation error, Eccentricity error

Question 106Single Answer

According to IS 800 : 2007, identify the property which is considered as a mechanical property of structural steel, important in design .

A
Unit mass
B
Maximum percent elongation on a standard gauge length
C
Co - efficient of thermal expansion
D
Poisson ration

Question 107Single Answer

Which of the following methods is NOT used for measuring air content in fresh concrete ?

A
Blaine air permeability method
B
Gravimetric method
C
Pressure method
D
Volumetric method

Question 108Single Answer

Which of the following methods is NOT used for the calculation of depreciation of a structure ?

A
Straight line method
B
Quantity survey method
C
Geometric projection method
D
Declining balance method

Question 109Single Answer

The failure of an over reinforced concrete beam is due to :

A
compression failure
B
mid failure
C
shear failure
D
tension failure

Question 110Single Answer

In which type of estimate is 'Court yard' NOT considered ?

A
Unit rate estimate
B
Plinth area estimate
C
Lump sum estimate
D
Cub rate estimate

Question 111Single Answer

Match the items in List 1 (name of quantities) with those in List 2 (unit of quantities in the SI system). Use codes in List for matching .
List 1 List 2
M. Dynamic viscosity 1. N/m
N. Kinematic viscosity 2. N.m
O. Surface tension 3. N.s/m²
P. Energy 4. m²/s

A
M-3, N-4, O-2, P-1
B
M-3, N-4, O-1, P-2
C
M-4, N-3, O-1, P-2
D
M-2, N-4, O-1, P-3

Question 112Single Answer

A reinforced concrete beam is subjected to the following bending moments .
Moment due to dead load = 50 kNm
Moment due to live load = 50 kNm
Moment due to seismic load = 20 kNm
The design bending moment for limit state of collapse is :

A
120 kNm
B
180 kNm
C
144 kNm
D
150 kNm

Question 113Single Answer

In a workshop shade, trusses are spaced at 4 m centre to centre. The purlins are spaced at 1.4 m centre to centre along the slope of 30⁰. The (Dead Load + Live load) is 3 kNm² and the wind load in 5 kNm². The vertical and the inclined point loads, respectively, will be :

A
14.54 kN and 28 kN
B
17.8 kN and 48 kN
C
20 kN and 24 kN
D
18 kN and 21 kN

Question 114Single Answer

What will be the percentage of passing aggregate for the grading zone 1 of sieve size 1.18 mm ?

A
100%
B
10% - 20%
C
7% - 25%
D
30% - 70%

Question 115Single Answer

The annual or periodical payment for repayment of the capital amount invested on a property for a specified period is known as :

A
depreciation
B
obsolescence
C
amortization
D
annuity

Question 116Single Answer

Among the following river training works, which are aligned either parallel or at an angle to the banks, identify the one having a difference in alignment when compared to others :

A
Flood walls
B
Guide banks
C
Groynes
D
Levees

Question 117Single Answer

The test commonly to determine the grade of bitumen in terms of its hardness is :

A
the penetration test
B
the ductility test
C
the softening point test
D
the flash and fire point test

Question 118Single Answer

A level section has formation width of 10 m, side slope of 1 : 2 (vertical : horizontal) and central height of 2 m. Determine the quantity of earthwork required for a 1 km length of formation (in m³) .

A
24,000
B
20,000
C
18,000
D
28,000

Question 119Single Answer

Which type of odour characteristic is NOT used for classifying odour of a given water sample as per IS 3025 (part-5) 1983 ?

A
Degree of sweetness
B
Degree of turbidity
C
Degree of pungency
D
Degree of smokiness

Question 120Single Answer

The liquid limit and plastic limit of clay materials is 45% and 25% respectively, what is the activity of clay materials if 20% by weight of particles of size less than 2 microns ?

Question 121Single Answer

Among the following corrections applied for tape measurement, identify the correction which is NOT always negative in sign :

A
Sag
B
Slope of taype
C
Pull
D
Wrong alignment

Question 122Single Answer

A village has a population of 200 with as average rate of water demand as 100 litre per capita per day. A rapid sand filter having an average filtration rate of 100 litre/hour/m² is to be designed for water treatment. The area of rapid sand filter required is : (Take the ratio of maximum demand to average demand as 1.5.)

A
8.00 m²
B
14.50 m²
C
10.00 m²
D
12.50 m²

Question 123Single Answer

If the bearing of the side AB of a regular hexagon traverse ABCDFFA shown in the figure is 36^o45', the bearing of the adjacent side BC of the traverse is :

A
216^o15'
B
96^o45'
C
83^o15'
D
156^o45'

Question 124Single Answer

Pigment volume concentration (PVC) of paint is defined as :

Question 125Single Answer

The Indian Roads Congress (IRC) was founded in the year :

A
1927
B
1934
C
1950
D
1982

Question 126Single Answer

In a leveling survey work, the first staff reading taken in a staff station after shifting the instrument and the last staff reading taken to a staff sation before the instrument in shifted are, respectively :

A
back sight and intermediate sight
B
intermediate sight and back sight
C
back sight and fore sight
D
fore sight and back sight

Question 127Single Answer

Which of the following Indian Standard Codes provides conservatively imposed loads for buildings and structures ?

A
IS 875 (part 4) – 1987
B
IS 875 (part 1) – 1987
C
IS 875 (part 3) – 1987
D
IS 875 (part 2) – 1987

Question 128Single Answer

Activity of soil is ratio of the plasticity index to :

A
percentage of compressive strength
B
percentage by weight of clay fraction
C
liquidity index
D
percentage of sensitivity

Question 129Single Answer

Kor watering in irrigation is defined as :

A
the first watering which is given to seeds sown in the plot for germination
B
the first watering which is given to a crop when the crop is a few centimeters high
C
the first watering which is given to a crop before transplanting
D
the first watering which is given to a plot when the crop is transplanted

Question 130Single Answer

What is a SI unit for dynamic viscosity ?

A
Pascal second
B
Pascal
C
Stoke
D
Newton

Question 131Single Answer

Arrange the following building materials in the increasing order of density of materials .
Granite, Steel, River sand, Water

A
Water, River sand, Steel, Granite
B
River sand, Granite, Water, Steel
C
River sand, Water, Granite, Steel
D
Water, River sand, Granite, Steel

Question 132Single Answer

The bearing of a line AB is 150^o15' and the angle ABC between line AB and BC is 110^o30' as shown in the given figure .

What is the bearing of line BC ?

A
440^o45'
B
80^o45'
C
79^o15'
D
330^o15'

Question 133Single Answer

Select the correct statement with respect to a slow sand filter :

A
The filtering medium has effective size 0.45 to 0.7 mm, uniformity coefficient 1.3 to 1.7, multiple graded layers of sand with bacteria and odour removal
B
The rate of filtration is in the range of 100 - 150 m³/m²/day
C
The effective size of sand particles shall be 0.15 to 0.3 mm, and their uniformity coefficient shall be preferably below 3
D
Backwashing daily or on alternate days is necessary for cleaning

Question 134Single Answer

What will be the carrying capacity of a horizontal rectangular channel 4 m wide, conveying a discharge of 1 cumecs per meter width of channel ?

A
4.000 m³/s
B
2.085 m³/s
C
1.000 m³/s
D
8.000 m³/s

Question 135Single Answer

Select the correct option with regard to the following statements (S1, S2) pertaining to consolidation in soils :
S1: A soil is termed as normally consolidated, if the present effective orver burden pressure is less than maximum to which the soil was ever been subjected to in the past .
S2: The large the value of co - efficient of consolidation, the shorter it takes for full consolidation to occur .

A
S1 is true and S2 is false
B
Both S1 and S2 are false
C
Both S1 and S2 are true
D
S1 is false and S2 is true

Question 136Single Answer

A real fluid in which the shear stress is directly proportional to the velocity gradient is known as :

A
non - newtonian fluid
B
newtonian fluid
C
ideal fluid
D
plastic fluid

Question 137Single Answer

An airport runway fill needs 8,50,000 m³ of soil compacted to void ratio of 0.7. The required soil is to be taken from a borrow pit having an in situ void ratio of 0.8. If the transportation cost is Rs.10 per m³, estimated cost for the filling work is (in Rs.) :

A
82,00,000
B
90,00,000
C
50,00,000
D
85,00,000

Question 138Single Answer

If p is internal pressure, d is diameter and t is thickness of wall for a thin cylindrical shell, then the value of hoop stress will be :

A
pt/4d
B
pd/4t
C
pd/2t
D
td/4p

Question 139Single Answer

As per IS 800 : 2007, in the design of beams/plate girders, when the web of a member acting alone is inadequate, different types of stiffeners are provided. Match the type of stiffeners provided in List 1 with the requirement to be satisfied by them in List 2 .
(Use the Code in the lists for matching)
List 1 List 2
B. Intermediate transverse wed stiffener 1. Provide local reinforcement to wed under shear and bearing
C. Load carrying stiffiener 2. Improve the buckling strength of a slender Web due to shear
D. Bearing stiffener 3. Prevent local buckling of web due to concentrated loading
E. Diagonal stiffener 4. Prevent local crushing of web due to concentrated loading

A
B - 3, C - 2, D - 4, E - 1
B
B - 4, C - 3, D - 1, E - 2
C
B - 2, C - 3, D - 4, E - 1
D
B - 4, C - 3, D - 2, E - 1

Question 140Single Answer

A canal was designed for a full supply discharge of 60 cumee. The average supply discharge in the canal is 40 cumee. The capacity factor of the cannal is :

A
6.0
B
4.00
C
0.67
D
0.45

Question 141Single Answer

Sewers must be checked for minimum velocities at their minimum hourly flows which is equal to :

A
1/4 average daily flows
B
1/2 average daily flows
C
average daily flows
D
1/3 average daily flows

Question 142Single Answer

What is the permissible limit of organic mater present in water for mixing concrete as per IS 456 - 2000 ?

A
200 mg/ l
B
3000 mg/ l
C
2000 mg/ l
D
400 mg/ l

Question 143Single Answer

A horizontal pipeline AB of diameter d cpmveus water, flowing from A to B. The U - tube manometer with mercury as manometric liquid can be used for the measurement of :

A
difference in the total energy between two points A and B
B
difference in the pressure head between two points A and B
C
difference in the velocity between the points A and B
D
difference in the kinetic head at the two points A and

Question 144Single Answer

A cantilever of beam span l is fixed at one end, the other end resting freely on the middle of a simply supported cross-beam of the same span and section. If the cantilever beam is now loaded with a uniform load of w per unit length, find the reaction at the free end offered by the cross beam.

Question 145Single Answer

Select the INCORRECT obstacle in chaining in a chain survey:

A
Obstracle to ranging only
B
Obstracle to chanining only
C
Obstracle to plotting
D
Obstracle to chanining and ranging

Question 146Single Answer

The basis for classification of ordinary Portland cement (OPC) as grade 33, 43 and 53 as per IS 10262 is :

A
28 days compressive strength
B
fineness value and setting time
C
soundness value
D
setting time

Question 147Single Answer

The mass of a chunk of moist soil is 20 kg and its dry density is 1500 kg/m³. What is the void ratio of the soil if the specific gravity is 2.50 and density of water is 10000 kg/m³

A
66.67%
B
72.35%
C
44.45%
D
56.67%

Question 148Single Answer

The maximum effective slenderness ratio for the compression flange of a steel beam against lateral torsional bucking as per IS 800 - 2007 is :

A
400
B
180
C
250
D
300

Question 149Single Answer

As old building has a future life of 15 years. The rate of interest on capital is 7%. If the coefficient of annual sinking fund is 0.43, then what will be value of year's purchase?

A
4
B
3
C
2.36
D
2

Question 150Single Answer

The value used for the prevention of reversal of flow in a pipeline is :

A
an air value
B
a check
C
a scour value
D
a butterfly value

Question 151Single Answer

In earthquake resistant design, response reduction factor (R) for steel special moment resisting frame (SMF) design as per IS 800 : 2000 is :

A
1.5
B
5.0
C
1.0
D
2.5

Question 152Single Answer

In mix design for M25 concrete, the assumed standard deviation for estimation of target mean strength of concrete mix, as recommended by IS 456 : 2000 is (in N/mm²) :

A
5.0
B
4.5
C
3.5
D
4.0

Question 153Single Answer

Which of the following CANNOT be considered as a hard surface lining of cannal ?

A
Boulder lining
B
Soil cement lining
C
Asphaltic concrete lining
D
Plaster lining

Question 154Single Answer

The following radings were obtained during differential leveling.
Reduced Level (RL) of point A is 240.000 m. The fore sight and back sight between points A and TPI in 1.420 m and 2.024 m, respectively. Fore sight and back sight between points TP1 and TP2 is 2.100 m and 1.986 m, respectively. The back sight from B is 1.722 m. These are marked on the givenfigure. What is the RL at turning point – 2 (TP2)? All values are in meteres.

A
242.024
B
241.202
C
240.604
D
240.490

Question 155Single Answer

Which of the following actions is NOT a permanent adjustment in case of trasit theodolite ?

A
Axis of the telescope levewl adjusted to paralled to the line of collimation
B
Axis of the plate level adjusted to perpendicular to vertical axis
C
Bringing the vertical axis of the theorolite exactly over the station mark
D
Horizontal axis is perpendicular to vertical axis when the instrument is levelled

Question 156Single Answer

Which of the following actions is NOT a permanent adjustment in case of trasit theodolite ?

A
Axis of the telescope levewl adjusted to paralled to the line of collimation
B
Axis of the plate level adjusted to perpendicular to vertical axis
C
Bringing the vertical axis of the theorolite exactly over the station mark
D
Horizontal axis is perpendicular to vertical axis when the instrument is levelled

Question 157Single Answer

The ability of a material in endure alternate wet and dry conditions for a long period without considerable deformation and loss of mechanical strength is called :

A
chemical resistance
B
fire resistance
C
weathering resistance
D
frost resistance

Question 158Single Answer

A newly built hose is let out for a rent of Rs. 1,000 per month inclusive of all taxes. If outgoings are at 20% of the gross rent and expected rate of return is 10%, what is the capital value by the rental method of valuation ?

A
Rs. 99,600
B
Rs. 1,12,300
C
Rs. 87,600
D
Rs. 96,000

Question 159Single Answer

What is the approximate composition of silicon dioxide (SiO²) present in ordinary Portland cement ?

A
60 - 67%
B
17 - 25%
C
40 - 50%
D
3 - 8%

Question 160Single Answer

The following statements (C1, C2, C3, C4) pertain in the characteristics of different type of canals. Which of the following statements is/are correct ?
C1 : A contour canal can irrigate command areas on both the banks.
C2 : If is possible to constract a contour canal with banks on one side only
C3 : In the case of a ridge canal, the number of cross drainage works are maximum.
C4 : Side slope canal is aligned roughly at right angles to the ground contours.

A
C1 only
B
C2 and C4 only
C
C1, C3 and C4 only
D
C1 and C3 only

Numerical, GK & Reasoning

Question 161Single Answer

Yojna a weekly journal

A
Ministry of Finance
B
Ministry of Information and Broadcastin
C
Ministry of Rural Development
D
Planning Commission

Question 162Single Answer

Kurukshetra a journal on rural development is published by

A
Ministry of Finance
B
Ministry of Information and Broadcastin
C
Ministry of Rural Development
D
Planning Commission

Question 163Single Answer

Devaluation of a currency means

A
Fixing the value of the currency in conjuction with the movement in the value of a basket of predetermined currencies
B
Reduction in the value of a currency vis-à-vis major internationally traded currencies
C
Fixing the value of currency in multilateral consultaion with the IMF the World Bank and major trading partners
D
Permitting the currency to seek its worth in the international market

Question 164Single Answer

Who is the Cabinet Minister for public enterprises ?

A
Dr. Damodar Rout
B
Debi Prasad Mishra
C
Jogendra Behera
D
Pradip Kumar Amat

Question 165Single Answer

Who is the minister of State of Commerce & Transport ?

A
Prafulla Kumar Mallick
B
Usha Devi
C
Ramesh Chandra Majhi
D
Arun Kumar Sahoo
E
Pradip Kumar Amat

Question 166Single Answer

What is the total Area (in sq. km) of Odisha ?

A
1,55,707 sq. km
B
1,047,553 sq. km
C
2,033,124 sq. km
D
1,88,697 sq. km

Question 167Single Answer

What is the literacy rate of Odisha (in %) ?

A
68.74 %
B
77.42 %
C
36.93 %
D
73.45 %

Question 168Single Answer

How many such pairs of letters are there in the word ‘CLEANLINESS’ each of the which has as many letters between them in the word as they have in the English alphabet, in the same sequence?

A
Two
B
Three
C
Five
D
Four
E
None of these

Question 169Single Answer

Team A has scored more goals than Team B
Team C has scored fewer goals than Team B
Team A has scored fewer goals than Team C .
If the first two statements are true, the third statement is

A
True
B
False
C
Uncertain
D
None

Question 170Single Answer

If it is possible to make only one meaningful word with the second, the third, the sixth and the eight letters of the word FRAGMENT using each only once, which of the following will be the third letter of that word ? If no such word can be formed, give ‘X’ as the answer and if more than one such word can be formed, give ‘Y’ as the answer.

Question 171Single Answer

How many such letters are there in the word ORIENTAL each of which is as far away from the beginning of the word as when they are arranged alphabetically?

A
None
B
One
C
Two
D
Three
E
More than three

Question 172Single Answer

How many such pairs of letters in the word CREDIT each of which has as many letters between them in the word as in the English alphabet?

A
None
B
One
C
Two
D
Three
E
More than three

Question 173Single Answer

How many meaningful words can be made from the letters ‘LMEA’ using each letter only once in each word?

A
None
B
One
C
Two
D
Three
E
More than three

Question 174Single Answer

The cash difference between the selling prices of an article at a profit of 4% and 6% is Rs. 3. The ratio of the two selling prices is:__________ ?

A
51:52
B
52:53
C
51:53
D
52:55

Question 175Single Answer

Which of the following numbers is irrational ?

A
√49
B
0.125
C
√2
D
22/7

Question 176Single Answer

356 x 936 – 356 x 836 = ?

A
35600
B
34500
C
9630
D
93600

Question 177Single Answer

Arrange in descending order: 5/8, 7/10, 3/4

A
3/4 > 7/10 > 5/8
B
7/10 > 3/4 > 5/8
C
3/4 > 5/8 > 7/10
D
5/8 > 7/10 > 3/4

Question 178Single Answer

What is (3^{^}{4} times 9^{^}{2}) ?

A
3⁶
B
3⁸
C
3¹⁰
D
9⁶

Question 179Single Answer

If 3⁴X^-2 = 729, then find the value of X.

Question 180Single Answer

Who became the longest-serving continuous Finance Minister of India and presented her ninth straight Union Budget on February 1, 2026?

A
Nirmala Sitharaman
B
Arun Jaitley
C
Pranab Mukherjee
D
P. Chidambaram

English Knowledge

Question 181Single Answer

I go to Madurai by —– Vaigai Express

A
a
B
an
C
some
D
the

Question 182Single Answer

Have the car stolen!

A
Steal the car
B
You should have the stolen car
C
Get someone to steal the car
D
They have stolen the car

Question 183Single Answer

The payment was collected by the hardworking salesman.

A
The hardworking salesman collected the payment.
B
the salesman who worked heard was able to collect the payment.
C
to collect the payment the salesman had to work hard.
D
The hardworking salesman was able to collect the payment.

Question 184Single Answer

I had to stop all my work to complete this project.

A
All other work had to be stopped to complete this project by me
B
For completing this project all other work must be stopped
C
For completing this project I had to stop all my work
D
To complete this project all other work had been stopped by me

Question 185Single Answer

They have published the names of all the successful candidates.

A
The candidates who have succeeded their names they had published.
B
The names of all the successful candidates have been published by them
C
The candidates who have succeeded their names have been published by them.
D
The names of all the successful candidate were published by them.

Question 186Single Answer

The online shopping site lowered the prices.

A
Lowering of the prices was done by the online shopping site
B
The prices were lowered by the online shopping site
C
The prices had been lowered by the online shopping site
D
The prices have been lowered by the online shopping site

Question 187Single Answer

Who taught you to drive a truck ?

A
To drive a truck by whom were you taught?
B
Driving a truck by who were you taught?
C
Driving a truck by who were you being taught?
D
By whom were you taught to drive a truck?

Question 188Single Answer

We shall invite Suresh.

A
Suresh would be invited by us
B
Suresh would have been invited by us
C
Suresh will be invited by us
D
Suresh will have been invited by us

Question 189Single Answer

Passage :

Direction : Question below has two blanks, each blank indicting that some thing has been omitted. Choose the word for each blank which best fits the meaning of the sentence as a whole.

The Finance Department has ……………a centralized online databank system for all statutory government bodies to …………an eye on their assets and liabilities.

A
presented , stay
B
introduced , keep
C
announce , make
D
created , let
E
proclaimed , hold

Question 190Single Answer

Passage :

Direction : The five items in this section consists of a word or group of words followed by four words as (a), (b), (c) and (d). Select the word which is nearly opposite to the meaning of the original word or group of words and mark your response as (a), (b), (c) and (d), as the case may be, in your Answer Sheet.

Assets

A
liabilities
B
responsibilities
C
estates
D
profits

Question 191Single Answer

Passage :

Direction : In the question, out of the four alternatives, choose the word which is opposite in meaning to the given word and click the button corresponding to it

Affidavit

A
Affirmation
B
Slander
C
Oath
D
Testimony

Question 192Single Answer

Passage :

Direction: In the following question, out of the four alternatives, choose the word which is opposite in meaning to the given word and click the button corresponding to it

Hollow

A
Alveolate
B
Cleft
C
Cavernous
D
Solid

Question 193Single Answer

Passage :

Directions: In the following question, out of the four alternatives, choose the word which is opposite in meaning to the given word and click the button corresponding to it

Cosset

A
Ignoreb
B
Close
C
Caress
D
Fondle

Question 194Single Answer

Passage :

Directions: In the following question, out of the four alternatives, choose the word which is opposite in meaning to the given word and click the button corresponding to it

Ogle

A
Leer
B
Gaze
C
Ignore
D
Gawk

Question 195Single Answer

Passage :

Directions:In the following question, out of the four alternatives, choose the word which is opposite in meaning to the given word and click the button corresponding to it

Intrinsic

A
Elemental
B
Innate
C
Connate
D
Acquired

Question 196Single Answer

Passage :

Direction : In the following question, out of the four alternatives, choose the word which is opposite in meaning to the given word and click the button corresponding to it

Coalesce

A
Separate
B
Adhere
C
Cleave
D
Amalgamate

Question 197Single Answer

Passage :

Directions: In the following question, out of the four alternatives, choose the word which is opposite in meaning to the given word and click the button corresponding to it

Loiter

A
lag
B
Hasten
C
Amble
D
Loii

Question 198Single Answer

Passage :

Direction : Question below has two blanks, blank indicating that something has been omitted. Choose the set of words for blank which best fits the meaning of the sentence as a whole.

The protests were......... at ......... awareness among the elite and the educated.

A
held, generating
B
aimed, creating
C
targeted, awakening
D
focused, building
E
concentrated, producing

Question 199Single Answer

Passage :

Directions:In the following question, out of the four alternatives, choose the word which is opposite in meaning to the given word and click the button corresponding to it

Deep-seated

A
Chronic
B
Temporary
C
inbred
D
Subconscious

Question 200Single Answer

Passage :

Directions: In the following question, out of the four alternatives, choose the word which is opposite in meaning to the given word and click the button corresponding to it

Vibrant

A
Drab
B
Gaudy
C
Jazzy
D
Vivid

Back to Exam

Latest OPTCL JMT Exam Question (Objective Questions), MCQ in English

Civil

OPTCL JMT Exam Online Question Bank Package

Civil

Numerical, GK & Reasoning

English Knowledge

Quick View