Download AppGovt. JobsFree G.K. & Current AffairsScholarshipBlog
Free PracticeContact
📚 Exam by Category
▾
Objective Questions

Latest SJVN Junior Field Engineer Electrical Exam Question (Objective Questions), MCQ in English

Subjects : Electrical, General Knowledge, Reasoning, Mathematics, Language and Behavioral Aptitude

Question Bank SJVN Junior Field Engineer (Electrical) Exam - English
Back to Exam

Electrical

Question 1Single Answer
Resistance switching is normally resorted in case of
  1. A
    Air blast CB
  2. B
    Bulk oil CB
  3. C
    Minimum oil CB
  4. D
    All types of CB
Question 2Single Answer
By transmitting power at high voltage
  1. A
    it will give poor voltage regulation
  2. B
    it will give better voltage regulation
  3. C
    it will not effect voltage regulation
  4. D
    None of these
Question 3Single Answer
Which statement about the daily load curve is valid ?
  1. A
    The area under the curve gives the average demand
  2. B
    The ratio of the area under the curves to the total area of rectangle in which it is contained gives the load factor for the day
  3. C
    The peak of the curve gives the installed capacity of the plant
  4. D
    The area of the curves divided by the number of hours gives load factor
Question 4Single Answer
High voltage Schring bridge is used to measure
  1. A
    large capacitance without additional element
  2. B
    small capacitance without additional element
  3. C
    medium value capacitance
  4. D
    None of these
Question 5Single Answer
Draw - in - system of laying underground cables has the drawback (s) of
  1. A
    higher cost
  2. B
    reduced current carrying capacity of the cables
  3. C
    requirements of much deeper and wider trenches
  4. D
    repairs, alterations or additions difficult
  5. E
    all of the above except
Question 6Single Answer
Surge impedance of a transmission line is
  1. A
    independent of its length
  2. B
    dependent on its length
  3. C
    independent on its temperature
  4. D
    none of the above
Question 7Single Answer
If two synchronous generators connected in parallel loose synchronism, it will lead to
  1. A
    stalling of generators
  2. B
    wild fluctuations in current
  3. C
    wild fluctuations in current and voltage
  4. D
    None of these
Question 8Single Answer
A differential relay responds to
  1. A
    algebraic difference of two or more similar electrical quantities
  2. B
    vector difference of two or more similar electrical quantities
  3. C
    algebraic difference between two currents
  4. D
    algebraic difference between two voltages
Question 9Single Answer
The conductor carries more current on the surface in comparison to its core. This phenomenon is called the
  1. A
    Skin effect
  2. B
    Corona
  3. C
    Ferranti effect
  4. D
    Lenz's effect
Question 10Single Answer
A booster is connected in
  1. A
    series with the feeder
  2. B
    parallel with the feeder
  3. C
    both (a) and (b) are correct
  4. D
    none of these
Question 11Single Answer
Fuses have got advantages of
  1. A
    cheapest type of protection
  2. B
    inverse time - current characteristic
  3. C
    no maintenance
  4. D
    current limiting effect under short - circuit conditions
  5. E
    all of the above
Question 12Single Answer
The power transmitted will be maximum when
  1. A
    line reactance is high
  2. B
    corona losses are minimum
  3. C
    sending end voltage is more
  4. D
    receiving end voltage is more
Question 13Single Answer
The connected load of a consumer is 2 kW and his maximum demand is 1.5 kW. The load factor of the consumer is
  1. A
    0.75
  2. B
    0.375
  3. C
    1.33
  4. D
    None of these
Question 14Single Answer
In a transformer, the exciting current will be in phase quadrature with the impressed voltage provided
  1. A
    only the leakage impedance drop is ignored
  2. B
    only the core loss is ignored
  3. C
    both the leakage impedance drop and the core loss are ignored
  4. D
    only the no - load copper loss is ignored
Question 15Single Answer
Which of the following techniques is used for the measurements of a.c. high frequency voltages ?
  1. A
    Peak voltmeter
  2. B
    Series resistance mircro - ammeter
  3. C
    Resistance potential divider
  4. D
    All of these
Question 16Single Answer
Use of additional shunt capacitor can be made for increasing the capability of line as it
  1. A
    reduces surge impedance Z0
  2. B
    increases phase shift β
  3. C
    increase in α
  4. D
    all of the above
Question 17Single Answer
The sag of a transmission line is least affected owing to
  1. A
    weight of the conductor
  2. B
    current through the conductor
  3. C
    atmospheric temperature
  4. D
    ice deposited on the conductor
Question 18Single Answer
In case of Impulse Thermal break down of solid insulating materials, the critical electric field is proportional to
  1. A
    critical absolute temperature
  2. B
    square of critical absolute temperature
  3. C
    square of T0
  4. D
    none of these
Question 19Single Answer
The insulation of the modern EHV lines is designed based on
  1. A
    corona
  2. B
    switching voltages
  3. C
    lightning voltage
  4. D
    all of these
Question 20Single Answer
For constant voltage transmission, the voltage drop along the line is maintained constant by installing
  1. A
    capacitors
  2. B
    inductors
  3. C
    resistors
  4. D
    synchronous phase modifiers at the receiving end
Question 21Single Answer
AC network analyser is employed for solving the problems of
  1. A
    load flow
  2. B
    load flow and stability
  3. C
    load flow and short - circuit
  4. D
    load flow, stability and short - circuit
Question 22Single Answer
The change in excitation in an alternator connected to an infinite line provides a corresponding change in
  1. A
    terminal voltage
  2. B
    speed of rotor
  3. C
    power generated
  4. D
    power factor
Question 23Single Answer
Different types of insulators used for transmission lines are
  1. A
    pin type only
  2. B
    suspension type only
  3. C
    strain type only
  4. D
    pin type, suspension type and shackle type
Question 24Single Answer
The conductor connecting consumer's terminals to the distributor is called the
  1. A
    feeder
  2. B
    distributor
  3. C
    service main
  4. D
    none of the above
Question 25Single Answer
Which of the following method or techniques can be used for the measurement of high d.c. voltages ?
  1. A
    Generating voltmeter
  2. B
    Electrostatic voltmeter
  3. C
    Peak voltmeter
  4. D
    Half effect generators
Question 26Single Answer
The ripple voltage in dc output is small if
  1. A
    frequency of supply voltage is small
  2. B
    the filtering capacitor is small
  3. C
    load current is small
  4. D
    none of these
Question 27Single Answer
The voltage measurements using uniform spark gap are
  1. A
    affected by dust particles
  2. B
    affected by polarity of supply
  3. C
    affected by temperature
  4. D
    none of these
Question 28Single Answer
Neutral earthing is provided for
  1. A
    the safety of personnel from electric shock
  2. B
    the safety of equipment and personnel against lightning and voltage surges
  3. C
    reducing the voltage stress on lines and equipment with respect to earth under various operating and fault conditions
  4. D
    controlling the earth fault currents for protective relaying
  5. E
    both (c) and (d)
Question 29Single Answer
The function of Lightning arrester is
  1. A
    to limiting the short - circuit fault current
  2. B
    to provide path to high voltage surge to earth
  3. C
    to reduce arcing
  4. D
    none of these
Question 30Single Answer
In which of the following cases are delay fuses used ?
  1. A
    For the protection of light circuits
  2. B
    For the protection of power out - let circuits
  3. C
    For the protection of fluorescent lamps
  4. D
    For the protection of motors
Question 31Single Answer
In order to improve the voltage profile of the line, compensation is resorted by providing
  1. A
    capacitors at the receiving end
  2. B
    reactors at the receiving end
  3. C
    resistors at the receiving end
  4. D
    none of these
Question 32Single Answer
Skin effect in conductor is proportional to
  1. A
    (diameter of conductor) 1/2
  2. B
    diameter of conductor
  3. C
    (diameter of conductor)2
  4. D
    (diameter of conductor)4
Question 33Single Answer
The function of steel wire in an ACSR conductor is to
  1. A
    compensate for skin effect
  2. B
    take care of surges
  3. C
    provide additional mechanical strength
  4. D
    reduce inductance
Question 34Single Answer
A fault is more severe from the view point of RRRV if it is a
  1. A
    Short length fault
  2. B
    Medium length line fault
  3. C
    Long length line fault
  4. D
    None of these
Question 35Single Answer
Protective resistance to be connected between the sphere gap and the test equipment is required while measuring
  1. A
    power frequency and higher frequency a.c. voltage
  2. B
    power frequency and impulse voltage
  3. C
    all kinds of voltages
  4. D
    none of these
Question 36Single Answer
Series capacitor is used in a transmission line to
  1. A
    compensate the voltage drop
  2. B
    reduce line loss
  3. C
    limit short circuit current
  4. D
    improve load power factor
Question 37Single Answer
The passive element that is used as interconnecting element for the stable operation of interconnected system is
  1. A
    reactor
  2. B
    resistor
  3. C
    capacitor
  4. D
    resistor and capacitor
Question 38Single Answer
Corona loss in a transmission line is dependent on
  1. A
    diameter of the conductor
  2. B
    material of the conductor
  3. C
    height of the conductor
  4. D
    none of these
Question 39Single Answer
In a minimum oil circuit breaker the oil is used
  1. A
    to act as circuit breaking medium only
  2. B
    for circuit breaking and providing insulation
  3. C
    for providing insulation only
  4. D
    for none of the above purposes
Question 40Single Answer
Skin effect is
  1. A
    proportional to frequency
  2. B
    proportional to square of frequency
  3. C
    inversely proportional to frequency
  4. D
    independent of frequency
Question 41Single Answer
Rated making capacity of breaker is equal to
  1. A
     X rated symmetrical breaking capacity
  2. B
    2.55 X rated symmetrical breaking capacity
  3. C
    1 X rated symmetrical breaking capacity
  4. D
    none of these
Question 42Single Answer
The main reason for using high voltage for long distance power transmission is
  1. A
    reduction in transmission losses
  2. B
    reduction in time of transmission
  3. C
    increase in system reliability
  4. D
    none of the above
Question 43Single Answer
Bus - coupler is very essential in
  1. A
    single bus - bar arrangement
  2. B
    ring bus - bar arrangement
  3. C
    double bus, double breaker arrangement
  4. D
    main and transfer bus
Question 44Single Answer
With the rise in temperature, the insulation resistivity
  1. A
    remains unchanged
  2. B
    decreases linearly
  3. C
    increases linearly
  4. D
    reduces exponentially
Question 45Single Answer
The effect of bonding the cable is
  1. A
    to increase the effective resistance and inductance
  2. B
    to increase the effective resistance but reduce inductance
  3. C
    to reduce the effective resistance and inductance
  4. D
    to reduce the effective resistance but increase the inductance
Question 46Single Answer
Increase in temperature in overhead transmission lines causes
  1. A
    increase in stress and length
  2. B
    decrease in stress and length
  3. C
    decrease in stress but increase in length
  4. D
    none of the above
Question 47Single Answer
The insulation resistance of the cable decreases with the
  1. A
    increase in length of cable
  2. B
    decrease in length of cable
  3. C
    electric stresses
  4. D
    none of these
Question 48Single Answer
Corona has the disadvantage(s) of
  1. A
    power loss
  2. B
    interference with neighbouring communication circuits
  3. C
    introducing the harmonics, predominately third harmonics, into the transmission lines
  4. D
    all of the above
Question 49Single Answer
In a load duration curve for an intergrated power system the uppermost crest represents the energy contributed by
  1. A
    base power stations
  2. B
    major thermal stations
  3. C
    peaking hydro or gas turbine stations
  4. D
    non - conventional power stations
Question 50Single Answer
At bridge crossing and near the railway track ternary lead cables are used because they
  1. A
    are of high tensile strength
  2. B
    are of low coefficient of thermal expansion
  3. C
    are of low specific gravity
  4. D
    can withstand shocks and vibrations
Important Questions Package

SJVN Junior Field Engineer Electrical Exam Online Question Bank Package

Buy SJVN Junior Field Engineer Electrical Important Questions, MCQ, question answer in Hindi & English. It will help you to score high marks in SJVN Junior Field Engineer Electrical question bank 2026 in Online, PDF & Print study material.

+ Free Monthly Current Affairs, GK & more PDF Download
Sr.Package NameAmount
1.SJVN Junior Field Engineer (Electrical) Exam - Hindi
Description : 1000 Question with Answer.
₹101 [₹500]
2.SJVN Junior Field Engineer (Electrical) Exam - Hindi
Description : 1730 Question with Answer.
₹131 [₹500]
3.SJVN Junior Field Engineer (Electrical) Exam - English
Description : 1000 Question with Answer.
₹101 [₹500]
4.SJVN Junior Field Engineer (Electrical) Exam - English
Description : 2000 Question with Answer.
₹151 [₹500]
5.SJVN Junior Field Engineer (Electrical) Exam - Hindi
Description : 1000 Question & Answer Download in PDF (Send by Email)
₹151 [₹450]
6.SJVN Junior Field Engineer (Electrical) Exam - English
Description : 1000 Question & Answer Download in PDF (Send by Email)
₹151 [₹450]
7.SJVN Junior Field Engineer (Electrical) Exam Question Bank Book - Hindi
Description : 1000 Question with Answer (Printed Material)
₹390 [₹600]
8.SJVN Junior Field Engineer (Electrical) Exam Question Bank Book - English
Description : 1000 Question with Answer (Printed Material)
₹390 [₹600]
9.SJVN Junior Field Engineer (Electrical) Exam - Hindi (Old)
Description : 1000 Question with Answer
₹61 [₹500]
10.SJVN Junior Field Engineer (Electrical) Exam - Hindi (Old)
Description : 2000 Question with Answer
₹101 [₹500]
Back to Exam