One bag of Portland cement, 50 kg in weight, would normally have a bulk volume of

AsCu, a preservative for wood, developed by the Forest Research Institute, Dehradun, comprises of chemicals:

Consider the following statements related to autoclave bricks:
1.Less water absorption compared to other bricks.
2.Noise reduction
3.It is cheap compared to other types of bricks.
4.Requirement of bulk volume of mortar in joints being relatively less compared to other types of brick masonry.
5.Not recommended for outer walls. 
Which of the above statements are relevant to the use of ‘autoclave’ bricks? 

The minimum number of annular rings to be seen in every 2.54 cm in the radial direction from the core for timber to be classified as ‘Dense’ is

If the actual thickness of a brick masonry wall is 19 cm, its effective length is 2.70 m, its effective height is 2.82 m and its code specified stiffening coefficient is 1.2 then, for design considerations, the slenderness ratio of the wall will be taken as

Consider the following forms of water in a hydrated cement paste:
1.Capillary water
2.Chemically combined water
3.Interlayer water
4.Adsorbed water 
Which of the above forms of water will, on its/their removal, cause shrinkage of the paste? 

Consider the following statements:High early strength of cement is obtained as a result of
1.Fine grinding.
2.Decreasing the lime content
3.Burning at higher temperature
4.Increasing the quality of gypsum. 
Which of the above statements are correct? 

Consider the following statements related to ‘composite mortar’:
1.Addition of lime to cement mortar improves its workability
2.Composite mortar is obtained by adding 10% by weight of cement and mixing with water.
3.Composite mortar is not preferred in tall buildings.
4.Mechanical grinding is essential for developing composite mortar.Which of the above statements are true in this case? 

Consider the following statements related to ‘non-destructive testing’ of concrete:
1.Indentation test is used to assess the quality of concrete.
2.Resonant Frequency Method is based on a laboratory test.
3.Compressive strength of concrete is estimated through Pulse Velocity Measurement.
4.Dynamic modulus of Elasticity is determined by a Sonometer Test.
5.Thickness of concrete can be estimated by in-situ Rebound Hammer Test. 
Which of the above statements are correct? 

What is the amount of water required for a workable RC of mix 1 : 2: 4 by weight., when W/C is 0-60 and unit weight of concrete is 2400 kg/m³?

Which IS code is used for classification of timber for seasoning purposes?

Consider the following with regard to the application of preservation of timber:
1.Increase in the life span of the member
2.Increase in the strength of the timber
3.Removal of moisture
4.Prevention of growth of fungi by killing them 
Which of the above are correct?

The plies in plywood are so placed that the grains of each ply are

Which of the following is an ODD one as regards ‘requirement of good brick-earth’?

The compressive strength of heavy-duty bricks, as per IS : 2980-1962, should not be less than

Consider the following statements:
1.Brickwork will have high water tightness.
2.Brickwork is preferred for monument structures.
3.Bricks resist fire better than stones
4.Bricks of good quality shall have thin mortar bonds. 
Which of the above statements are correct?

Consider the following statements:A good soil for making bricks should contain
1.30% alumina
2.10% lime nodules
3.Only small quantity of iron oxides
4.15% magnesia 
Which of the above statements are correct?

Which compound of cement is responsible for strength of cement?

Which type of cement is recommended in large mass concrete works such as a dam?

Consider the following statements regarding ‘setting of cement’:
1.Low-heat cement sets faster than OPC.
2.Final setting time decides the strength of cement
3.Initial setting time of Portland Pozzollona is 30 minutes
4.Air-induced setting is observed when stored under damp conditions.
4.Addition of gypsum retards the setting time. 
Which of the above statements are correct? 

Consider the following statements regarding ‘strength of cement’:
1.Strength test on cement is made on cubes of cement-sand mix.
2.Water to be used for the paste is 0.25 P, where P is the water needed for normal consistency.
3.The normal consistency is determined on Le Chatelier’s principle.
4.Cubes are cast in two layers in leak-proof moulds further compacted in each layer by vibration on a machine. 
Which of the above statements are correct? 

Which of the following ingredients refer to binding material of mortar?
1.Cement
2.Lime
3.Sand
4.Ashes 
Select the correct answer using the code given below. 

Consider the following statements:
1.Bricks in masonry are bound by mortar.
2.Mortars make brick damp-proof.
3.Strength of brick in masonry is improved by plastering.
4.Addition of lime improves workability.
5.Marine construction needs sulphate-resistant cement mortar. 
Which of the above statements are relevant for ‘cement mortar’? 

Consider the following parameters of concrete:
1.Impermeability
2.Compactness
3.Durability
4.Desired consistency
5.Workability 
Which of the above parameters are relevant for ‘water-cement ratio’? 

Consider the following statements:Presence of Na₂O and K₂O in concrete leads to
1.Expansive reaction in concrete
2.Cracking of concrete
3.Disruption of concrete
4.Shrinkage of concrete 
Which of the above statements are correct? 

The maximum total quantity of dry aggregate by mass per 50 kg of cement, to be taken as the sum of the individual masses of fine and coarse aggregates (kg), for M20 grade of concrete is

Absorption capacity of an aggregate refers to the difference expresses in appropriate proportion in water content between

Consider the following statements concerning  ‘elasticity of concrete’:
1.Stress-strain behavior of concrete is a straight line up to 10% ultimate stress.
2.Strain determination is obtained from tangent modulus.
3.Modulus of elasticity of concrete is also called as secant modulus. 
Which of the above statements are correct? 

Consider the following statements :The addition of CaCl₂ in concrete results in
1.Increased shrinkage
2.Decreased setting time
3.Decreased shrinkage
4.Increased setting time 
Which of the above statements are correct? 

Which of the following statements are correct ?
1.Knots in a tree affect the continuity of fibres.
2.Nail knots do not influence the strength of timber.
3.Druxiness of wood is not a defect.
4.Tall trees with twisted fibers give good timber for poles.

Excrescences in wood are
1.Defects found in trees
2.Formed due to injuries inflicted on trees when they are growing
3.Defects which render wood suitable as firewood only

What treatment is adopted for making timber fire-resistant?

Deterioration of structure of timber due to dry rot is:
1.Caused by fungi
2.Due to dry-spell after heavy rains
3.Due to attack of termites
4.ndicated by surface stripes on scantlings  

Alternate wetting and drying of timber :
1.Results in shrinkage and swelling
2.Brings about wet rot onset
3.Increases the durability
4.Causes transmission of spores from germination  

As per I.S. classification, the minimum compressive strength of a first class brick should be

When provided with alternating courses of (a) all headers and (b) all stretchers, the front elevation of such brick masonry is designated as

I.S. code specifies that the compressive strength of brick shall be determined by keeping the brick:
1.On edge
2.On bed
3.After soaking in water for 2 hrs
4.After soaking in water for 24 hrs  

Soundness test of cement is carried out to determine its

The objectives of producing cement include:
1.Incorporating industrial wastes
2.Increasing free lime
3.Increasing fineness
4.Saving energy needed in the process  

A mild steel rod tapers uniformly from 24 mm  mm dia. over its length of 400 mm. The rod when held vertical is subjected to an axial tensile load of 12 kN. E = 2 × 10⁵ N/mm². The extension of the rod in mm would be:

Two different liquids are flowing through different pipes of the same diameter. In the first pipe, the flow is laminar with centerline velocity,V_max.1,Whereas in the second pipe, the flow is turbulent. For turbulent flow, the average velocity is 0.82 times the centerline velocity,v_max.2 . For equal volumetric flow rates in both the pipes, the ratio V_max.1/V_max.2(up to two decimal place) is_____.
 

Poisson’s ratio of a material is 0.3. Then the ratio of Young’s modulus to bulk modulus is

For a gas phase cracking reaction A→B+C at 300℃ , the Gibbs free energy of the reaction at this temperature is ∆G°= -2750J/mol . The pressure is 1 bar and the gas phase can be assumed to be ideal. The universal gas constant =8.314J/mol. K. The fractional molar conversion of A at equilibrium is________.
 

Which of the following statements are correct ?
1.In a ductile material elastic deformation is more predominant than plastic one.
2.Brittleness is not an absolute property of a metal.
3.Rate of loading has no influence in changing the behavior of a metal from ‘ductile’ to ‘brittle’ at low temperatures
4.Under hydrostatic compression, a brittle metal may change into a ductile one. 

The total deflection of a structure when subjected simultaneously to different sets of loading is equal to the sum of the deflections under each such set of loads as if acting separately on the structure. Which one the following justifies this statement?

A rectangular bar of cross-sectional area a is subjected to an axial tensile load P. The maximum shear stress will occur on a plane at X° to any normal cross-section where X° is

A solid circular shaft has been subjected to a pure torsion moment. The ratio of maximum shear stress to maximum normal stress at any point would be

Which of the following statements are correct?
1.All load carrying members transmit load through basic modes of tension, compression, torsion and shear only.
2.Beams carry transverse loads.
3.Combined loading is a complicated loading.
4.Nature of internal forces decides the aspect of combines loading. 

Identify the WRONG statement amongst the following:

Which of the following statements are correct?
1.Experimental results on thin-walled tubes show that maximum normal stress theory is valid.
2.Normal-stress theory is valid in case of brittle materials.
3.In case of pure shear, St. Venant’s theory is more valid than other theories.
4.Tresca’s theory is very closely substantiated by experimental results.
5.In maximum stress theory, the yield locus is a hexagon.  

Consider the following statements:
1. IS 3583 refers to Burnt Clay Paving Bricks.
2. IS 5779 refers to Burnt Clay Soling Bricks.
3. IS 3952 refers to Burnt Clay Hollow Bricks.
4. IS 2222 refers to Burnt Clay Lay Bricks.
Which of the above statements are correct?

Consider the following statements:
1. A high aggregate impact value indicates strong aggregates.
2. A low aggregate crushing value indicates high crushing strength of aggregates.
3. Aggregates having elongation index values greater than 15% are generally considered suitable for pavement construction.
4. Flakiness index of aggregates should not be less than 25% for use in road construction.
Which of the above statements are correct?

Consider the following statements regarding refractory bricks in furnaces:
1. The furnace is fired at temperatures more than 1700°C.
2. Silica content in the soil should be less than 40%.
3. Water absorption of bricks should not exceed 10%
4. Chrome bricks are known as basic bricks. Which of the above statements are correct?

Consider the following statements about lime:
1. Calcination of limestone results in quick lime.
2. Lime produced from pure variety of chalk is hydraulic lime.
3. Hydrated lime is obtained by treating quick lime with water.
Which of the above statements are correct?

Consider the following statements:
1. If more water is added to concrete for increasing its workability, it results into concrete of low strength.
2. No slump is an indication of a good workable concrete.
3. Higher the slump of concrete, lower will be its workability.
4. Workability of concrete is affected by water content as well as water-cement ratio.
Which of the above statements are correct?

Pozzolana used as an admixture in concrete has the following advantages:
1. It improves workability with lesser amount of water.
2. It increases the heat of hydration and so lets the concrete set quickly.
3. It increases the resistance of concrete to attack by salts and sulphates.
4. It leaches out calcium hydroxide.
Select the correct answer using the codes given below:

Consider the following statements regarding Cyclopean Concrete:
1. Size of aggregate is more than 150 mm.
2. Size of aggregate is less than 150 mm.
3. High slump.
4. High temperature rise due to heat of hydration.
Which of the above statements are correct?

A chain, working a crane, has sectional area of 625 mm² and transmits a load of 10 kN. When the load is being lowered at a uniform rate of 40 m/min, the chain gets jammed suddenly at which time the length of the chain unwound is 10m. Assuming E = 200 GPa, the stress induced in the chain due to this sudden jamming is

In mild steel specimens subjected to tensile test cycle, the elastic limit in tension is raised and the elastic limit in compression is lowered, This is called

Consider the following statements :
1. The shear stress distribution across the section of a circular shaft subjected to twisting varies parabolically.
2. The shear stress at the centre of a circular shaft under twisting moment is zero
3. The shear stress at the extreme fibres of a circular shaft under twisting moment is maximum.
Which of the above statements is/are correct?

The span of a cantilever beam is 2m. The cross-section of the beam is a hollow square with external sides 100 mm; and its 1 = 4 × 105 mm⁴. The safe bending stress for the beam material is 100 N/mm². The safe concentrated load at the free end would be

Consider the following statements in respect of arched construction made of voussoirs:
1. The superimposed load is transferred to the sidewalls only by the strength of cohesion of the mortar between the voussoirs.
2. The arch may fail under crushing when the compressive stress or thrust in it exceeds the safe crushing strength of the voussoir material.
3. Every element in the arch is subjected to compression only.
4. Failure of the arch due to the sliding of any voussoir past the adjacent one due to transverse shear can be avoided by reducing the height of the voussoirs.
Which of the above statements are correct?

Which of the following are examples of indeterminate structures?
1. Fixed beam
2. Continuous beam
3. Two-hinged arch
4. Beam overhanging on both sides
Select the correct answer using the codes given below:

A cantilever beam, 3m long, carries a uniformly distributed load over the entire length. If the slope at the free end is 1°, the deflection at the free end is

The maximum bending moment at a given section, in which a train of wheel loads moves occurs when the average load on the left segment is
1. Equal to the average load on the right segment.
2. More than the average load on the right segment.
3. Less than the average load on the right segment.
Select the correct answer using the codes given below:

A single degree of freedom system of mass 22 kg and stiffness 17 kN/m vibrates freely. If damping in the system is 2%, the cyclic frequency and the damped circular frequency, respectively, are nearly

A cable of insignificant weight, 18 m long, is supported at its two ends, 16m apart, at the same level. The cable supports at its mid-reach a load of 120 N. The tension in the cable is nearly

The design strength of a tension member is governed by
1. Rupture at a critical section
2. Yielding of gross area
3. Block shear of end region
Select the correct answer using the codes given below:

A beam-column is alternately bent either (1) in single curvature, or (2) in double curvature. The secondary moments induced are to be compared. These are indicated SM₁ and SM₂ as per the conditions (1) and (2) respectively

Gantry girders can be designed
1. As laterally supported beams.
2. As laterally unsupported beams.
3. By using channel sections.
Select the correct answer using the codes given below:

A three-hinged parabolic arch ABC has a span of 20 m and a central rise of 4·0 m. The arch has hinges at the ends and at the crown. A train of two point loads of 20 kN and 10 kN, 5 m apart, crosses this arch from left to right, with the 20 kN load leading. The maximum thrust induced at the supports is

According to IS : 875 Part 3, the design wind speed acting on industrial roof is estimated based on the basic wind speed by multiplying it by factors K₁,K₂ andK₃, where K₁ is called

Consider the following two statements regarding Bearing stiffeners provided at the location of a concentrated load:
1. Bearing stiffeners have to resist bearing and buckling loads.
2. Bearing area and the area resisting buckling load are the same.
Which of the above statements is/are correct?

In a plate girder, the web plate is connected to the flange plates by fillet welding. The size of the fillet welds is designed to safely resist

A certain R.C. short column with 300 mm square cross-section is made of M 20 grade concrete and has 4 numbers, 20 mm diameter, longitudinal bars of Fe 415 grade steel. It is under the action of a concentric axial compressive load. Ignoring the reduction in the area of concrete due to the steel bars, the ultimate axial load carrying capacity of the column as by the relevant code is