📚 Exam by Category
▾
Objective Questions

Latest VSSC Technical Assistant Exam Question (Objective Questions), MCQ in English

Subjects : Electronics, and Telecommunication

Question Bank VSSC Technical Assistant Exam (Electronics and Communication Engineering) - English
Back to Exam

Electronics, and Telecommunication

Question 1Single Answer
Which one of the following helps experimental confirmation of the Crystalline state of matter?
  1. A
    Shock compression
  2. B
    Photo emission
  3. C
    Conductivity measurements
  4. D
    X-ray diffraction
Question 2Single Answer
The electrical conductivity of pure semiconductor is:
  1. A
    Proportional to temperature
  2. B
    Increases exponentially with temperature
  3. C
    Decreases exponentially with temperature
  4. D
    Not altered with temperature
Question 3Single Answer
Consider the following statements pertaining to the resistance of a conductor:
1. Resistance can be simply defined as the ratio of voltage across the conductor to the current through the conductor. This is, in fact, Georg Ohm’s law.
2. Resistance is a function of voltage and current.
3. Resistance is a function of conductor geometry and its conductivity
Which of the above statements are correct?
  1. A
    1 and 2 only
  2. B
    2 and 3 only
  3. C
    1 and 3 only
  4. D
    1, 2 and 3
Question 4Single Answer
The ratio of ionic radii of Cations i.e.and that of Anions i.e.for stable and unstable ceramic crystal structure, is:
  1. A
    Less than unity
  2. B
    Greater than unity
  3. C
    Unity
  4. D
    Either lesser or greater than unity
Question 5Single Answer
Which one of the following statements is correct?
  1. A
    For insulators the band-gap is narrow as compared to semiconductors
  2. B
    For insulators the band-gap is relatively wide whereas for semiconductors it is narrow
  3. C
    The band-gap is narrow in width for both the insulators and conductors
  4. D
    The band-gap is equally wide for both conductors and semiconductors
Question 6Single Answer
In an extrinsic semiconductor the conductivity significantly depends upon:
  1. A
    Majority charge carriers generated due to impurity doping
  2. B
    Minority charge carriers generated due to thermal agitation
  3. C
    Majority charge carriers generated due to thermal agitation
  4. D
    Minority charge carriers generated due to impurity doping
Question 7Single Answer
In some substances when an electric field is applied the substance become polarized. The electrons and nucleii assume new geometrical positions and the mechanical dimensions are altered. This phenomenon is called:
  1. A
    Electrostriction
  2. B
    Hall-Effect
  3. C
    Polarization
  4. D
    Magnetization
Question 8Single Answer
In ferromagnetic materials, the net magnetic moment created due to magnetization by an applied field as:
  1. A
    Normal to the applied field
  2. B
    Adds to the applied field
  3. C
    In line with magneto motive force
  4. D
    Subtracts from the applied field
Question 9Single Answer
At what temperatures domains lose their ferromagnetic properties?
  1. A
    Above ferromagnetic Curie temperature
  2. B
    Below paramagnetic Curie temperature
  3. C
    Above 4
  4. D
    At room temperature
Question 10Single Answer
Which of the following materials does not have paramagnetic properties?
1. Rare earth elements (with incomplete shell)
2. Transition elements
3. Magnesium oxide
Select the correct answer from the codes given below:
  1. A
    1 only
  2. B
    2 only
  3. C
    3 only
  4. D
    1 and 2
Question 11Single Answer
In a superconducting magnet, wires of superconducting material are embedded in the thick copper matrix, because while the material is in the superconducting state:
  1. A
    The leakage current passes through copper part.
  2. B
    Copper part helps in conducting heat away from the superconductor
  3. C
    Copper part helps in overcoming the mechanical stress
  4. D
    Copper acts as an insulating cover for superconductor
Question 12Single Answer
The crystal structure of some Ceramic materials may be thought of being composed of electrically charged Cations and Anions, instead of Atoms, and as such:
  1. A
    The Cations are negatively charged, because they have given up their valence electrons to Anions which are positively charged.
  2. B
    The Cations are positively charged, because they have given up their valence electrons to Anions which are negatively charged.
  3. C
    The Cations are positively charged, because they have added one electron to their valence electron borrowing from Anions which are negatively charged.
  4. D
    The Cations are negatively charged, as they are non-metallic whereas Anions are positively charged being metallic.
Question 13Single Answer
Manganin alloy used for making resistors for laboratory instruments contains:
  1. A
    Copper, Aluminium and Manganese
  2. B
    Copper, Nickel and Manganese
  3. C
    Aluminium, Nickel and Manganese
  4. D
    Chromium, Nickel and manganese
Question 14Single Answer
A rolled-paper capacitor of value 0.02  is to be constructed using two strips of aluminiumof width 6 cm, and wax impregnated paper of thickness 0.06 mm whose relative permittivity is 3. The length of foil strips should be:
  1. A
    0.3765 m
  2. B
    0.4765 m
  3. C
    0.5765 m
  4. D
    0.7765 m
Question 15Single Answer
In a semiconductor diode, cut-in voltage is the voltage:
  1. A
    up to which the current is zero
  2. B
    up to which the current is very small
  3. C
    at which the current is 10% of the maximum rated current
  4. D
    at which depletion layer is formed
Question 16Single Answer
The transistor is operating in:
  1. A
    Saturation
  2. B
    Cut-off
  3. C
    Normal active
  4. D
    Reverse active
Question 17Single Answer
The leakage current in an NPN transistor is due to the flow of:
  1. A
    Holes from base to emitter
  2. B
    Electrons from collector to base
  3. C
    Holes from collector to base
  4. D
    Minority carriers from emitter to collector
Question 18Single Answer
In Early effect:
  1. A
    Increase in magnitude of collector voltage increase space charge width at the input junction of a BJT
  2. B
    Increase in magnitude of Emitter-Base voltage increases space charge width of output junction of a BJT
  3. C
    Increase in magnitude of Collector voltage increases space charge width of output junction of a BJT
  4. D
    Decrease in magnitude of Emitter-Base voltage increases space charge width of output junction of a BJT
Question 19Single Answer
Maximum energy of electrons liberated photo electrically is:
  1. A
    Proportional to light intensity and independent of frequency of the light.
  2. B
    Independent of light intensity and varies linearly with frequency of light
  3. C
    Proportional to both, light intensity and frequency of the light
  4. D
    Independent of light intensity and inversely proportional to frequency of the light
Question 20Single Answer
The response of a Gaussian random process applied to a stable linear system is:
1. A Gaussian random process
2. Not a Gaussian random process
3. Completely specified by its mean and auto covariance functions
Which of the above statements is/are correct?
  1. A
    1 only
  2. B
    2 only
  3. C
    2 and 3
  4. D
    1 and 3
Question 21Single Answer
Which of the following regions of operation are mainly responsible for heating of the transistor under switching operation?
1. Saturation region
2. Cut-off region
3. Transition from saturation to cut-off
4. Transition from cut-off to saturation
Select the correct answer using the codes given below
  1. A
    1, 2 and 4 only
  2. B
    1, 3 and 4 only
  3. C
    2 and 3 only
  4. D
    1 and 3 only
Question 22Single Answer
In a sinusoidal oscillator, sustained oscillations will be produced only if the loop gain (at the oscillation frequency) is
  1. A
    Less than unity but not zero
  2. B
    Zero
  3. C
    Unity
  4. D
    Greater than unity
Question 23Single Answer
The Class-B push-pull amplifier is an efficient two –transistor circuit, in which the two transistors operate in the following way:
  1. A
    Both transistors operate in the active region throughout the negative ac cycle
  2. B
    Both transistors operate in the active region for more than half-cycle but less than a whole cycle
  3. C
    One transistor conducts during the positive half-cycle and the other during the negative half-cycle
  4. D
    Full supply voltage appears across each of the transistors
Question 24Single Answer
PAC stands for______.
  1. A
    Permanent angle converter
  2. B
    Phase angle converter
  3. C
    Phase angle components
  4. D
    Phase angle capacitor
  5. E
    None of these
Question 25Single Answer
For normal operation of a transistor
  1. A
    Forward bias the emitter diode and reverse bias the collector diode
  2. B
    Forward bias the emitter diode as well as the collector diode
  3. C
    Reverse bias the emitter diode as well as the collector diode
  4. D
    Reverse bias the emitter diode and forward bias the collector diode
Question 26Single Answer
Consider the following statements regarding linear power supply:
1. It requires low frequency transformer.
2. It requires high frequency transformer.
3. The transistor works in active region.
Which of the above statements is/are correct?
  1. A
    1 only
  2. B
    2 and 3 only
  3. C
    1 and 3 only
  4. D
    3 only
Question 27Single Answer
A full wave rectifier connected to the output terminals of the mains transformer produces an RMS voltage of 18 V across the secondary. The no-load voltage across the secondary of the transformer is
  1. A
    1.62 V
  2. B
    16.2 V
  3. C
    61.2 V
  4. D
    6.12 V
Question 28Single Answer
MICR stands for______.
  1. A
    Magnetic Ink Chart Receipt
  2. B
    Magnetic Ink Character Recognition
  3. C
    Magnetic Ink Chart Recognition
  4. D
    Magnetic Ink capacitor Reverse
  5. E
    None of these
Question 29Single Answer
In an Op-Amp, if the feedback voltage is reduced by connecting a voltage divider at the output, which of the following will happen?
1. Input impedance increases
2. Output impedance increases
3. Overall gain increases
Which of the above statements is/are correct?
  1. A
    1 only
  2. B
    2 only
  3. C
    3 only
  4. D
    1, 2 and 3
Question 30Single Answer
The transient response rise time (unity gain) of an Op-Amp is 0.05s.The small signal bandwidth is
  1. A
    7 kHz
  2. B
    20 kHz
  3. C
    7 MHz
  4. D
    20 MHz
Question 31Single Answer
A negative feedback of   is applied to an amplifier of open-loop gain 1000. What is the change in overall gain of the feedback amplifier, if the gain of the internal amplifier is reduced by 20%?
  1. A
    295.7
  2. B
    286.7
  3. C
    275.7
  4. D
    266.7
Question 32Single Answer
If the quality factor of a single-stage single tuned amplifier is doubled, the bandwidth will
  1. A
    Remain the same
  2. B
    Become half
  3. C
    Become double
  4. D
    Become four times
Question 33Single Answer
Consider the following statements related to oscillator circuits:
1. The tank circuit of a Hartley oscillator is make up of a tapped capacitor and a common inductor.
2. The tank circuit of a Colpitts oscillator is make up of a tapped capacitor and a common oscillator.
3. The Wien Bridge oscillator is essentially a two-stage amplifier with an RC bridge in the first stage, and, the second stage serving as inverter.
4. Crystal oscillators are fixed frequency oscillators with a high Q-factor.
Which of the above statements are correct?
  1. A
    1, 2 and 3 only
  2. B
    2, 3 and 4 only
  3. C
    1, 2 and 4 only
  4. D
    1, 3 and 4 only
Question 34Single Answer
The most commonly used transistor configuration for use as a switching devices is
  1. A
    Common-base configuration
  2. B
    Common-collector configuration
  3. C
    Common-emitter shorted configuration
  4. D
    Common-emitter configuration
Question 35Single Answer
The simplified form of the Boolean expression AB + A (B + C) + B(B + C) is given by
  1. A
    AB + AC
  2. B
    B + AC
  3. C
    BC + AC
  4. D
    AB + C
Question 36Single Answer
What is the maximum frequency for a sine wave output voltage of 10 V peak with an Op-Amp whose slew rate is 1V/ ?
  1. A
    15.92 kHz
  2. B
    19.73 kHz
  3. C
    23.54 kHz
  4. D
    27.36 kHz
Question 37Single Answer
Which one of the following statements is correct?
  1. A
    TTL logic cannot be used un digital circuits
  2. B
    Digital circuits are linear circuits
  3. C
    AND gate is a logic circuit whose output is equal to its highest input.
  4. D
    In a four-input AND circuits, all inputs must be high for the output to be high.
Question 38Single Answer
The slew rate is the rate of change of output voltage of an operational amplifier when a particular input is applied. What is that input?
  1. A
    Sine wave input
  2. B
    Ramp input
  3. C
    Pulse input
  4. D
     Step input
Question 39Single Answer
Except at high frequencies of switching, nearly all the power dissipated in the switch mode operation of a BJT occurs, when the transistor is in the
  1. A
    Active region
  2. B
    Blocking state
  3. C
    Hard saturation region
  4. D
    Soft saturation region
Question 40Single Answer
Consider the following statements with respect to combinational circuit:
1. The output at any time depends only on the present combination of inputs.
2. It does not employ storage elements.
3. It     performs an operation that can be specified logically by a set of Boolean functions.
Which of the above statements are correct?
  1. A
    1 and 2 only
  2. B
    1 and 3 only
  3. C
    2 and 3 only
  4. D
    1, 2 and 3
Question 41Single Answer
Consider the following statements:
The output of a linear circuit, driven with a sine wave at a frequency f, is itself a sine wave
1. at the same frequency
2. with chance of changed amplitude
3. with chances of changed amplitude and phase
Which of the above statements is/are correct? 
  1. A
    1 and 2
  2. B
    1 only
  3. C
    1 and 3
  4. D
    2 only 
Question 42Single Answer
Consider the following statements:
The main contribution to photo conduction is by
1. the generation of electron and hole pair by a photon
2. a donor electron jumping into the conduction band because of a photon’s energy
3. a valence electron jumping into an acceptor state because of a photon’s energy Which of the above statements is/are correct? 
  1. A
    1 only
  2. B
    2 only
  3. C
    3 only
  4. D
    1, 2 and 3
Question 43Single Answer
Thermal runaway is not possible in FET because as the temperature of the FET increase
  1. A
    mobility decreases
  2. B
     trans-conductance increases
  3. C
    drain current increases
  4. D
    trans-conductance decreases
Question 44Single Answer
For the same network, with 6 V DC connected at port A, 1 Ω connected at port B draws 7/3 A. if 8 V DC is connected to port A, the open circuit voltage at port B is
  1. A
    6 V
  2. B
    7 V
  3. C
    8 V
  4. D
    9 V
Question 45Single Answer
A signal may have frequency components which lie in the range of 0.001 Hz to 10 Hz. Which one of the following types of couplings should be chosen in a multistage amplifier designed to amplify the signal? 
  1. A
    Capacitor coupling
  2. B
    Direct coupling
  3. C
    Transformer coupling
  4. D
    Double-tuned transformer coupling
Question 46Single Answer
If an input impedance of op-amp is finite, then which one of the following statements related to virtual ground is correct ? 
  1. A
    Virtual ground condition may exist.
  2. B
    Virtual ground condition cannot exist
  3. C
    In case of op-amp, virtual ground condition always exists.
  4. D
    Cannot make a valid declaration 
Question 47Single Answer
Hysteresis is desirable in a Schmitt-trigger because 
  1. A
    energy is to be stored/discharged in parasitic capacitances
  2. B
    effects of temperature variations would be compensated
  3. C
    devices in the circuit should be allowed time for saturating and de-saturation
  4. D
    it would prevent noise from causing false triggering 
Question 48Single Answer
In a photoconductive cell the resistance, of the semiconductor material varies with intensity of incident light. 
  1. A
    directly
  2. B
    inversely 
  3. C
    exponentially
  4. D
    logarithmically 
Question 49Single Answer
In graded index multimode optical fiber the refractive index of the core is
  1. A
    uniform across its radial distance except for the cladding
  2. B
    maximum at the fiber axis and decreased stepwise towards the cladding
  3. C
    maximum at the fiber axis and decreases gradually towards the cladding.
  4. D
    maximum at the fiber axis and increases stepwise towards the cladding
Question 50Single Answer
Consider the following factors:
1. Number of turns of the coil
2. Length of the coil
3. Area of cross-section of the coil
4. Permeability of the core
On which of the above factors does inductance, depend?
  1. A
    1, 2 and 3 only
  2. B
    1, 3 and 4 only
  3. C
    1, 2, 3 and 4
  4. D
    2 and 4 only 
Important Questions Package

VSSC Technical Assistant Exam Online Question Bank Package

Buy VSSC Technical Assistant Important Questions, MCQ, question answer in Hindi & English. It will help you to score high marks in VSSC Technical Assistant question bank 2026 in Online, PDF & Print study material.

+ Free Monthly Current Affairs, GK & more PDF Download
Sr.Package NameAmount
1.VSSC Technical Assistant (Mechanical) Exam - English
Description : 1000 Question with Answer.
₹101 [₹500]
2.VSSC Technical Assistant (Mechanical) Exam - English
Description : 2000 Question with Answer.
₹151 [₹500]
3.VSSC Technical Assistant Exam (Computer Science) - English
Description : 1000 Question with Answer.
₹101 [₹500]
4.VSSC Technical Assistant Exam (Computer Science) - English
Description : 2000 Question with Answer.
₹151 [₹500]
5.VSSC Technical Assistant Exam (Electronics and Communication Engineering) - English
Description : 1150 Question with Answer.
₹101 [₹500]
6.VSSC Technical Assistant Exam (Electronics and Communication Engineering) - English (Old)
Description : 1100 Question With Answer
₹101 [₹500]
7.VSSC Technical Assistant Exam (Computer Science) - English (Old)
Description : 1000 Question With Answer
₹101 [₹500]
8.VSSC Technical Assistant Exam (Mechanical) - English (Old)
Description : 1000 Question & Answer Download in PDF (Send by Email)
₹151 [₹450]
Back to Exam
Question for ISRO VSSC Technical Assistant 2026 - Quiz / Questions / MCQ - Toppersexam